首頁 電源管理 多通道 IC (PMIC)
首頁
電源管理
多通道 IC (PMIC)
最新

LP87743-Q1

現行

適用於雷達 MMIC 的汽車、三路 3A 低雜訊降壓轉換器 PMIC

立即訂購
產品規格表

LP87743-Q1

現行
產品規格表 立即訂購

產品詳細資料

Processor supplier Texas Instruments Processor name mmWave AWR, mmWave IWR Regulated outputs (#) 3 Step-down DC/DC converter 3 Vin (min) (V) 3 Vin (max) (V) 4 Vout (min) (V) 0.9 Vout (max) (V) 1.8 Iout (max) (A) 3 TI functional safety category Functional Safety-Compliant Configurability Factory programmable, Software configurable Features Output Short-Circuit and Overload Protection, Overtemperature warning and protection, Overvoltage protection, SPI, UVLO Rating Automotive Operating temperature range (°C) -40 to 125 Step-down DC/DC controller 0 Step-up DC/DC controller 0 Iq (typ) (mA) 0.02 Switching frequency (max) (kHz) 19200 Shutdown current (ISD) (typ) (µA) 20 Switching frequency (typ) (kHz) 17600 Product type Radar sensor
Processor supplier Texas Instruments Processor name mmWave AWR, mmWave IWR Regulated outputs (#) 3 Step-down DC/DC converter 3 Vin (min) (V) 3 Vin (max) (V) 4 Vout (min) (V) 0.9 Vout (max) (V) 1.8 Iout (max) (A) 3 TI functional safety category Functional Safety-Compliant Configurability Factory programmable, Software configurable Features Output Short-Circuit and Overload Protection, Overtemperature warning and protection, Overvoltage protection, SPI, UVLO Rating Automotive Operating temperature range (°C) -40 to 125 Step-down DC/DC controller 0 Step-up DC/DC controller 0 Iq (typ) (mA) 0.02 Switching frequency (max) (kHz) 19200 Shutdown current (ISD) (typ) (µA) 20 Switching frequency (typ) (kHz) 17600 Product type Radar sensor
VQFN-HR (RXV) 28 22.5 mm² 5 x 4.5
  • AEC-Q100 qualified with the following results:
    • Device temperature grade 1: –40°C to +125°C ambient operating temperature
  • Functional safety-compliant device
    • Developed for functional safety applications
    • Documentation available to aid ISO 26262 functional safety system design up to ASIL-C / SIL-2
    • Input supply overvoltage and undervoltage monitoring
    • Regulator output overvoltage and undervoltage monitoring
    • Overvoltage and undervoltage monitoring for one external rail
    • Q&A watchdog
    • Level or PWM error signal monitor (ESM)
    • BIST and CRC
  • Input voltage: 3.3V nominal (3V to 4V range)
  • Three low-noise step-down DC/DC converters:
    • Output voltage: 0.9V to 1.9V, 0.8V (BUCK3), 0.82V (BUCK3)
    • Maximum output current: 3A/ 3A/ 3A
    • Switching frequency: 4.4MHz, 8.8MHz, and 17.6MHz
  • 5V boost converter
    • Maximum output current: 350mA
  • 150mA LDO
    • Output voltage 1.8V or 3.3V
  • Output short-circuit and overload protection
  • Input overvoltage protection (OVP) and undervoltage lockout (UVLO)
  • Overtemperature warning and protection
  • Serial peripheral interface (SPI)
  • AEC-Q100 qualified with the following results:
    • Device temperature grade 1: –40°C to +125°C ambient operating temperature
  • Functional safety-compliant device
    • Developed for functional safety applications
    • Documentation available to aid ISO 26262 functional safety system design up to ASIL-C / SIL-2
    • Input supply overvoltage and undervoltage monitoring
    • Regulator output overvoltage and undervoltage monitoring
    • Overvoltage and undervoltage monitoring for one external rail
    • Q&A watchdog
    • Level or PWM error signal monitor (ESM)
    • BIST and CRC
  • Input voltage: 3.3V nominal (3V to 4V range)
  • Three low-noise step-down DC/DC converters:
    • Output voltage: 0.9V to 1.9V, 0.8V (BUCK3), 0.82V (BUCK3)
    • Maximum output current: 3A/ 3A/ 3A
    • Switching frequency: 4.4MHz, 8.8MHz, and 17.6MHz
  • 5V boost converter
    • Maximum output current: 350mA
  • 150mA LDO
    • Output voltage 1.8V or 3.3V
  • Output short-circuit and overload protection
  • Input overvoltage protection (OVP) and undervoltage lockout (UVLO)
  • Overtemperature warning and protection
  • Serial peripheral interface (SPI)

The LP8774x-Q1 device is designed to meet the power management requirements of the AWR and IWR MMICs in various automotive and industrial radar applications. The device has three step-down DC/DC converters, a 5V boost converter and a 1.8V or 3.3V LDO. The LDO is powered from the boost and intended for xWR I/O supply. An SPI serial interface and enable signals control the device.

The step-down DC/DC converters support programmable switching frequency of 4.4MHz, 8.8MHz, or 17.6MHz. High switching frequency and low noise across wide frequency range enable LDO-free power solution with minimal or no passive filtering. The high switching frequency improves thermals and transient settling for the MMIC RF rails. The device forces the switching clock into PWM mode for optimal RF performance and can also be synchronized to an external clock. The device supports remote voltage sensing to compensate IR drop between the regulator output and the point-of-load (POL) which improves the accuracy of the output voltage.

The LP8774x-Q1 device supports programmable start-up and shutdown delays and sequences which are synchronized to the ENABLE signal. The sequences can also include GPO signals to control external regulators, load switches, and processor reset. The default settings for the device are programmed into nonvolatile memory (NVM). The device controls the output slew rate to minimize output voltage overshoot and in-rush current during device start-up.

The LP8774x-Q1 device is designed to meet the power management requirements of the AWR and IWR MMICs in various automotive and industrial radar applications. The device has three step-down DC/DC converters, a 5V boost converter and a 1.8V or 3.3V LDO. The LDO is powered from the boost and intended for xWR I/O supply. An SPI serial interface and enable signals control the device.

The step-down DC/DC converters support programmable switching frequency of 4.4MHz, 8.8MHz, or 17.6MHz. High switching frequency and low noise across wide frequency range enable LDO-free power solution with minimal or no passive filtering. The high switching frequency improves thermals and transient settling for the MMIC RF rails. The device forces the switching clock into PWM mode for optimal RF performance and can also be synchronized to an external clock. The device supports remote voltage sensing to compensate IR drop between the regulator output and the point-of-load (POL) which improves the accuracy of the output voltage.

The LP8774x-Q1 device supports programmable start-up and shutdown delays and sequences which are synchronized to the ENABLE signal. The sequences can also include GPO signals to control external regulators, load switches, and processor reset. The default settings for the device are programmed into nonvolatile memory (NVM). The device controls the output slew rate to minimize output voltage overshoot and in-rush current during device start-up.
filter 尋找其它 多通道 IC (PMIC)
下載 觀看有字幕稿的影片 影片
索取更多資訊

提供完整產品規格表和其它資訊。立即索取

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 1
類型 標題 日期
* Data sheet LP8774x-Q1 Three Buck Converters and 5-V Boost for AWR and IWR Radar Sensors datasheet (Rev. B) PDF | HTML 2024年 6月 24日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

LP877451Q1EVM — 適用於 ADAS PMIC 低雜訊配置 3 降壓和 5-V 升壓的 LP8774x-Q1 評估模組

LP8774x-Q1 裝置設計旨在滿足各種汽車與工業雷達應用中的 AWR 和 IWR MMIC 電源管理需求。裝置配備三個降壓式 DC/DC 轉換器、5 V 升壓轉換器和 1.8 V/3.3 V LDO。LDO 由升壓供電，且旨在供 xWR 與週邊裝置 IO 電源使用。本裝置由 SPI 序列介面及啟用訊號控制。

降壓式 DC/DC 轉換器支援 17.6 MHz、8.8 MHz 或 4.4 MHz 的可編程切換頻率，並在廣泛頻率範圍中擁有低雜訊，能以最小被動式濾波或無需額外被動式濾波，實現免 LDO 的電源解決方案。LP8774x-Q1 (...)

使用指南: PDF | HTML
View Options
模擬型號

LP87745-Q1 BUCK PSpice Transient Model

SNVMCA5.ZIP (46 KB) - PSpice Model
下載
模擬型號

LP87745-Q1 Transient and AC SIMPLIS Buck Model (Rev. C)

SNVMC81C.ZIP (65 KB) - SIMPLIS Model
下載
計算工具

PEET-GUI — PMIC 效率評估器工具 (PEET)

The PMIC Efficiency Estimator Tool (PEET GUI) is a graphical user interface used to easily evaluate PMIC DC/DC regulator efficiency relative to your design conditions. The PEET GUI can be used to configure each DC/DC regulator separately and provides real-time efficiency and power dissipation data (...)
在雲端評估
參考設計

TIDEP-01030 — 適‌用於高階轉角雷達的 mmWave 診斷和監控參考設計

此參考設計展示了 mmWave 雷達感測器中內建自動監控功能，此功能可透過降低主機上的處理負載來提高系統效率。此設計使用安全診斷資料庫 (SDL) 對可編程數位核心、週邊設備和記憶體執行診斷測試。此設計也會配置並啟用不同硬體元件的 RF 和類比監控功能。透過協助使用者利用各種安全資源來實現符合汽車安全完整性等級 (ASIL B) 和安全完整性等級 (SIL 2) 標準的產品，此參考設計加快了整體開發時間和上市時間。
Design guide: PDF
參考設計

TIDEP-01027 — 高端角雷達參考設計

TIDA-01027 參考設計使用 AWR2944 評估模組 (EVM) 為角雷達應用提供良好基礎，以符合 NCAP R79 安全要求。此設計讓使用者能在裝置視野 (FoV) 最遠 200 公尺下，估計並追蹤裝置位置 (在方位角平面) 與物體速度。此應用著重於邊角與前端長距離雷達系統的多項功能，例如盲點偵測、前交叉路口輔助及車道變換輔助功能。另外也展示了 TI 壓縮引擎和硬體加速器 (HWA) 功能的使用狀況。
Design guide: PDF
電路圖: PDF
封裝 針腳 CAD 符號、佔位空間與 3D 模型
VQFN-HR (RXV) 28 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片