首頁 電源管理 LED 驅動器 汽車 LED 驅動器
首頁
電源管理
LED 驅動器
汽車 LED 驅動器

TPS92643-Q1

現行

車用 3-A 同步降壓 LED 驅動器

立即訂購
產品規格表

TPS92643-Q1

現行
產品規格表 立即訂購

產品詳細資料

Number of channels 1 Topology Buck Rating Automotive Operating temperature range (°C) -40 to 125 Vin (min) (V) 5 Vin (max) (V) 42 Vout (min) (V) 4.5 Vout (max) (V) 33 Iout (max) (A) 3 Iq (typ) (mA) 56 Switching frequency (max) (kHz) 2200 Features Fault Detection, LED Open Detection, Precision Dimming Control, Thermal shutdown
Number of channels 1 Topology Buck Rating Automotive Operating temperature range (°C) -40 to 125 Vin (min) (V) 5 Vin (max) (V) 42 Vout (min) (V) 4.5 Vout (max) (V) 33 Iout (max) (A) 3 Iq (typ) (mA) 56 Switching frequency (max) (kHz) 2200 Features Fault Detection, LED Open Detection, Precision Dimming Control, Thermal shutdown
HTSSOP (PWP) 16 32 mm² 5 x 6.4
  • AEC-Q100 qualified for automotive applications
    • Grade 1: –40°C to 125°C ambient operating temperature
    • Device HBM classification level H1C
    • Device CDM classification level C5
  • Input voltage range: 5.5 V to 36 V
    • Operation down to 5.15 V after start-up
  • Up to 3-A continuous with 4% accuracy
  • Adaptive on-time current control
    • Low offset high-side current sense amplifier
    • Stable with any combination of ceramic, and aluminum capacitors
  • Programmable switching frequency from 100 kHz to 2.2 MHz
  • Advanced dimming operation
    • 1000:1 precision PWM dimming
    • 15:1 precision analog dimming
    • 1.4-kHz internal analog input to PWM duty cycle translation
  • Cycle-by-cycle switch overcurrent protection
  • Open-drain fault indicator output
    • LED short circuit, open circuit and cable harness fault indication
  • Thermal shutdown protection
  • AEC-Q100 qualified for automotive applications
    • Grade 1: –40°C to 125°C ambient operating temperature
    • Device HBM classification level H1C
    • Device CDM classification level C5
  • Input voltage range: 5.5 V to 36 V
    • Operation down to 5.15 V after start-up
  • Up to 3-A continuous with 4% accuracy
  • Adaptive on-time current control
    • Low offset high-side current sense amplifier
    • Stable with any combination of ceramic, and aluminum capacitors
  • Programmable switching frequency from 100 kHz to 2.2 MHz
  • Advanced dimming operation
    • 1000:1 precision PWM dimming
    • 15:1 precision analog dimming
    • 1.4-kHz internal analog input to PWM duty cycle translation
  • Cycle-by-cycle switch overcurrent protection
  • Open-drain fault indicator output
    • LED short circuit, open circuit and cable harness fault indication
  • Thermal shutdown protection

The TPS92643-Q1 is a monolithic, synchronous Buck LED driver with a wide 5.5-V to 36-V operating input voltage range and 40-V tolerance that supports load dump for duration of 400 ms. The TPS92643-Q1 implements an adaptive on-time average current mode control based on inductor valley current detection. The adaptive on-time control provides near constant switching frequency that can be set between 100 kHz and 2.2 MHz. Inductor current sensing and closed-loop feedback enables better than ±4% accuracy over wide input, output and ambient temperature.

The high-performance LED driver can independently modulate LED current using both analog or PWM dimming techniques. Linear analog dimming range with over 15:1 range is obtained by setting the IADJ voltage. PWM dimming of LED current is achieved by directly modulating the UDIM input pin with desired duty cycle or setting the analog voltage at APWM to enable internal analog-to-PWM conversion. The internal PWM generator translates the external analog voltage by comparing it to an internal 1.4-kHz ramp signal.

The TPS92643-Q1 incorporates advanced diagnostic and fault protection featuring: cycle-by-cycle switch current limit, bootstrap undervoltage, LED open, LED short and thermal shutdown.

The TPS92643-Q1 is available in a 6.6-mm × 5.1-mm thermally-enhanced 16-pin HTSSOP package with 0.65-mm lead pitch.

The TPS92643-Q1 is a monolithic, synchronous Buck LED driver with a wide 5.5-V to 36-V operating input voltage range and 40-V tolerance that supports load dump for duration of 400 ms. The TPS92643-Q1 implements an adaptive on-time average current mode control based on inductor valley current detection. The adaptive on-time control provides near constant switching frequency that can be set between 100 kHz and 2.2 MHz. Inductor current sensing and closed-loop feedback enables better than ±4% accuracy over wide input, output and ambient temperature.

The high-performance LED driver can independently modulate LED current using both analog or PWM dimming techniques. Linear analog dimming range with over 15:1 range is obtained by setting the IADJ voltage. PWM dimming of LED current is achieved by directly modulating the UDIM input pin with desired duty cycle or setting the analog voltage at APWM to enable internal analog-to-PWM conversion. The internal PWM generator translates the external analog voltage by comparing it to an internal 1.4-kHz ramp signal.

The TPS92643-Q1 incorporates advanced diagnostic and fault protection featuring: cycle-by-cycle switch current limit, bootstrap undervoltage, LED open, LED short and thermal shutdown.

The TPS92643-Q1 is available in a 6.6-mm × 5.1-mm thermally-enhanced 16-pin HTSSOP package with 0.65-mm lead pitch.
filter 尋找其它 汽車 LED 驅動器
下載 觀看有字幕稿的影片 影片

您可能會感興趣的類似產品

open-in-new 比較替代產品
引腳對引腳且具備與所比較裝置相同的功能
最新 TPS92642-Q1 現行 車用同步降壓紅外線 LED 驅動器 Pin-to-pin replacement supporting up to 4-A LED pulsed current.
功能相同，但引腳輸出與所比較的裝置不同
TPS92518-Q1 現行 具有 SPI 介面、類比和 PWM 調光的 42-V 車用雙降壓 LED 控制器 Dual-channel buck controller with SPI.
TPS92520-Q1 現行 具有 SPI 的 1.6-A 雙同步降壓 LED 驅動器 Dual-channel monolithic buck regulator with SPI.

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 1
類型 標題 日期
* Data sheet TPS92643-Q1 Automotive 3-A Synchronous Buck LED Driver datasheet PDF | HTML 2022年 5月 12日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TPS92643EVM-204 — 適用於汽車 3-A 同步降壓 LED 驅動器的 TPS92643-Q1 評估模組

TPS92643EVM-204 評估模組 (EVM) 可協助設計人員評估針對高電流 LED 驅動應用設計的 TPS92643-Q1 3.0-A 降壓切換穩壓器的操作與性能。TPS92643-Q1 設計旨在控制高亮度發光二極體 (LED)，具備廣泛的輸入電壓範圍 (5.5 V 至 40 V)、PWM 調光功能、類比調光功能、輸入欠電壓防護、故障偵測、內部 5-V 穩壓器，以及對板載 1.4-kHz PMW 訊號執行工作週期控制的能力。

使用指南: PDF | HTML
TI.com 無法提供
模擬工具

PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具

PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
要求
封裝 針腳 CAD 符號、佔位空間與 3D 模型
HTSSOP (PWP) 16 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片