TPS63000-Q1

現行

車用 1.8V 至 5.5V 輸入範圍、1.8A 高效降壓/升壓轉換器

alarm通知 立即訂購

產品詳細資料

Rating Automotive Operating temperature range (°C) -40 to 125 Topology Buck-Boost Type Converter Vin (min) (V) 1.8 Vin (max) (V) 5.5 Switching frequency (min) (kHz) 1250 Switching frequency (max) (kHz) 1500 Features Enable, Frequency synchronization, Light Load Efficiency, Load Disconnect, Synchronous Rectification, UVLO Fixed Vout (min) (V) 1.2 Vout (max) (V) 5.5 Iq (typ) (µA) 40 Duty cycle (max) (%) 100 Switch current limit (typ) (A) 1.8
Rating Automotive Operating temperature range (°C) -40 to 125 Topology Buck-Boost Type Converter Vin (min) (V) 1.8 Vin (max) (V) 5.5 Switching frequency (min) (kHz) 1250 Switching frequency (max) (kHz) 1500 Features Enable, Frequency synchronization, Light Load Efficiency, Load Disconnect, Synchronous Rectification, UVLO Fixed Vout (min) (V) 1.2 Vout (max) (V) 5.5 Iq (typ) (µA) 40 Duty cycle (max) (%) 100 Switch current limit (typ) (A) 1.8
VSON (DRC) 10 9 mm² 3 x 3
  • Qualified for Automotive Applications
  • Up to 96% Efficiency
  • 1200-mA Output Current at 3.3 V in Step Down
    Mode (VIN = 3.6 V to 5.5 V)
  • Up to 800-mA Output Current at 3.3 V in Boost
    Mode (VIN > 2.4 V)
  • Automatic Transition between Step Down and Boost Mode
  • Device Quiescent Current Less Than 50 µA
  • Input Voltage Range: 1.8 V to 5.5 V
  • Adjustable Output Voltage From 1.2 V to 5.5 V
  • Power Save Mode for Improved Efficiency at
    Low Output Power
  • Forced Fixed Frequency Operation and
    Synchronization Possible
  • Load Disconnect During Shutdown
  • Over-Temperature Protection
  • Available in Small 3 mm × 3 mm, QFN-10 Package
  • APPLICATIONS
    • All Two-Cell and Three-Cell Alkaline,
      NiCd or NiMH or Single-Cell Li Battery
      Powered Products
    • Portable Audio Players
    • PDAs
    • Cellular Phones
    • Personal Medical Products
    • White LEDs

PowerPAD Is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.

  • Qualified for Automotive Applications
  • Up to 96% Efficiency
  • 1200-mA Output Current at 3.3 V in Step Down
    Mode (VIN = 3.6 V to 5.5 V)
  • Up to 800-mA Output Current at 3.3 V in Boost
    Mode (VIN > 2.4 V)
  • Automatic Transition between Step Down and Boost Mode
  • Device Quiescent Current Less Than 50 µA
  • Input Voltage Range: 1.8 V to 5.5 V
  • Adjustable Output Voltage From 1.2 V to 5.5 V
  • Power Save Mode for Improved Efficiency at
    Low Output Power
  • Forced Fixed Frequency Operation and
    Synchronization Possible
  • Load Disconnect During Shutdown
  • Over-Temperature Protection
  • Available in Small 3 mm × 3 mm, QFN-10 Package
  • APPLICATIONS
    • All Two-Cell and Three-Cell Alkaline,
      NiCd or NiMH or Single-Cell Li Battery
      Powered Products
    • Portable Audio Players
    • PDAs
    • Cellular Phones
    • Personal Medical Products
    • White LEDs

PowerPAD Is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.

The TPS63000 devices provide a power supply solution for products powered by either a two-cell or three-cell alkaline, NiCd or NiMH battery, or a one-cell Li-Ion or Li-polymer battery. Output currents can go as high as 1200 mA while using a single-cell Li-Ion or Li-Polymer battery, and discharge it down to 2.5 V or lower. The buck-boost converter is based on a fixed frequency, pulse-width-modulation (PWM) controller using synchronous rectification to obtain maximum efficiency. At low load currents, the converter enters Power Save mode to maintain high efficiency over a wide load current range. The Power Save mode can be disabled, forcing the converter to operate at a fixed switching frequency. The maximum average current in the switches is limited to a typical value of 1800 mA. The output voltage is programmable using an external resistor divider. The converter can be disabled to minimize battery drain. During shutdown, the load is disconnected from the battery. The device is packaged in a 10-pin QFN PowerPAD package measuring 3 mm × 3 mm (DRC).

The TPS63000 devices provide a power supply solution for products powered by either a two-cell or three-cell alkaline, NiCd or NiMH battery, or a one-cell Li-Ion or Li-polymer battery. Output currents can go as high as 1200 mA while using a single-cell Li-Ion or Li-Polymer battery, and discharge it down to 2.5 V or lower. The buck-boost converter is based on a fixed frequency, pulse-width-modulation (PWM) controller using synchronous rectification to obtain maximum efficiency. At low load currents, the converter enters Power Save mode to maintain high efficiency over a wide load current range. The Power Save mode can be disabled, forcing the converter to operate at a fixed switching frequency. The maximum average current in the switches is limited to a typical value of 1800 mA. The output voltage is programmable using an external resistor divider. The converter can be disabled to minimize battery drain. During shutdown, the load is disconnected from the battery. The device is packaged in a 10-pin QFN PowerPAD package measuring 3 mm × 3 mm (DRC).

下載 觀看有字幕稿的影片 影片

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件,然後再試一次。
檢視所有 8
類型 標題 日期
* Data sheet High-Efficiency Single-Inductor Buck-Boost Converter With 1.8-A Switches datasheet 2009年 6月 24日
Application note QFN and SON PCB Attachment (Rev. C) PDF | HTML 2023年 12月 6日
Application note Different Methods to Drive LEDs Using TPS63XXX Buck-Boost Converters (Rev. D) 2021年 8月 4日
Application note Layer Design for Reducing Radiated EMI of DC to DC Buck-Boost Converters (Rev. A) PDF | HTML 2021年 6月 9日
Application note Performing Accurate PFM Mode Efficiency Measurements (Rev. A) 2018年 12月 11日
Application note Understanding Undervoltage Lockout in Power Devices (Rev. A) 2018年 9月 19日
Analog Design Journal Design considerations for a resistive feedback divider in a DC/DC converter 2012年 4月 26日
Analog Design Journal IQ: What it is, what it isn’t, and how to use it 2011年 6月 17日

設計與開發

如需其他條款或必要資源,請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TPS63000EVM-148 — TPS63000 5.5V 輸入、3.3V 輸出、1A 降壓-升壓轉換器評估模組基板

Evaluation Module Board for Buck-Boost Converter 5.5V Input, 3.3V Output, 1A

The TPS63000EVM-148 is an evaluation tool for the TPS63000 device family. It is a 96% efficient Buck/Boost Converter with an input range of 1.8 V to 5.5 V, optimized to run from a single-cell Li-Ion battery (...)

使用指南: PDF
向經銷商購買
計算工具

SLVC808 Battery Lifetime Estimator

支援產品和硬體

支援產品和硬體

產品
AC/DC 和 DC/DC 轉換器 (整合式 FET)
TPS63000 採用 3x3 QFN,具有 1.8A 電流開關的高效降壓-升壓轉換器 TPS63000-Q1 車用 1.8V 至 5.5V 輸入範圍、1.8A 高效降壓/升壓轉換器 TPS63001 採用 3x3 QFN 封裝,具有 1.7A 電流開關、3.3V 固定輸出電壓的 96% 降壓-升壓轉換器 TPS63002 採用 3x3 QFN 封裝,具有 1.7A 電流開關、5V 固定輸出電壓的 96% 降壓-升壓轉換器 TPS63010 有 2-A 開關的高效率、單電感器、降壓升壓轉換器 TPS63011 有 2-A 開關的高效率、單電感器、降壓升壓轉換器 TPS63012 有 2-A 開關的高效率、單電感器、降壓升壓轉換器 TPS63020 具 4A 開關的高效率、單電感器、降壓升壓轉換器 TPS63020-Q1 具 4A 開關的高效率車用單電感器降壓升壓轉換器 TPS63021 具 4A 開關的高效率、單電感器、降壓升壓轉換器 TPS63024 高效率 1.5A 單電感器降壓-升壓轉換器 TPS630241 高效率 1.5A 單電感器降壓-升壓轉換器 TPS630242 高效率 1.5A 單電感器降壓-升壓轉換器 TPS630250 採用 3.7 mm² DSBGA 封裝的 4-A 開關單電感器降壓-升壓轉換器 TPS630251 採用 WCSP 的 4A 開關單電感器降壓-升壓轉換器 TPS630252 採用 WCSP 的 4A 開關單電感器降壓-升壓轉換器 TPS63027 高效率 4.5A 開關單電感器降壓-升壓轉換器 TPS63030 有 1-A 開關的高效率、單電感器、降壓升壓轉換器 TPS63031 有 1-A 開關的高效率、單電感器、降壓升壓轉換器 TPS63036 有 1-A 開關的高效率、單電感器、降壓升壓轉換器 TPS63050 具 1-A 開關和可調式緩啓動的 TPS6305x 單電感器降壓升壓 TPS63051 小型單電感器降壓/升壓轉換器 TPS63060 2.5V 至 12V 輸入電壓、93% 效率、2.25A 開關電流限制、降壓升壓轉換器 TPS63060-EP 具 2-A 開關電流的高輸入電壓降壓升壓轉換器 TPS63061 2.5V 至 12V 輸入電壓、93% 效率、2.25A 開關電流限制、降壓升壓轉換器 TPS63070 寬輸入電壓 (2V-16V) 降壓-升壓轉換器 TPS63700 採用 3x3 QFN 封裝的可調式 -15V 輸出反向 DC/DC 轉換器 TPS63710 採用 3x3 WSON 封裝的低雜訊、1A 同步反向降壓轉換器 TPS63802 採用 QFN/DFN 封裝的 2A 高效率、11-µA 靜態電流降壓升壓轉換器 TPS63805 具有小型解決方案尺寸的 2-A、高效率、11-µA 靜態電流降壓-升壓轉換器 TPS63806 採用小巧 WCSP 具有最佳化的負載步進回應的 2.5A 高效降壓-升壓轉換器 TPS63807 2A、11-uA 靜態電流降壓-升壓轉換器 TPS63810 適用於動態電壓負載,具有 I²C 介面的 2.5A 高效降壓-升壓轉換器 TPS63811 適用於動態電壓負載,具有 I²C 介面的 2.5A 高效降壓-升壓轉換器 TPS63900 具有輸入電流限制和動態電壓調整功能的 1.8V 至 5.5V、75nA IQ 降壓/升壓轉換器
封裝 針腳 CAD 符號、佔位空間與 3D 模型
VSON (DRC) 10 Ultra Librarian

訂購與品質

內含資訊:
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊:
  • 晶圓廠位置
  • 組裝地點

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

內容係由 TI 和社群貢獻者依「現狀」提供,且不構成 TI 規範。檢視使用條款

若有關於品質、封裝或訂購 TI 產品的問題,請參閱 TI 支援。​​​​​​​​​​​​​​

影片