Startseite Energiemanagement LED-Treiber Treiber für LED-Displays
Startseite
Energiemanagement
LED-Treiber
Treiber für LED-Displays

TLC5905

AKTIV

8/16-Kanal-LED-Treiber mit auswählbarem Timing für Datenausgang

Jetzt bestellen
Datenblatt

TLC5905

AKTIV
Datenblatt Jetzt bestellen

Produktdetails

Features Error Flag, PWM LED Driver, Power good, Thermal shutdown Analog dimming steps 32 Data transfer rate (typ) (MHz) 15 Ch to ch accuracy (typ) (±%) 4 Rating Catalog Operating temperature range (°C) -20 to 85
Features Error Flag, PWM LED Driver, Power good, Thermal shutdown Analog dimming steps 32 Data transfer rate (typ) (MHz) 15 Ch to ch accuracy (typ) (±%) 4 Rating Catalog Operating temperature range (°C) -20 to 85
HTQFP (PAP) 64 144 mm² 12 x 12
  • Drive Capability and Output Counts:
    • 80 mA (Current Sink) × 16 Bits
    • 120 mA (Current Sink) × 8 Bits
  • Constant Current Output Range:
    • 5 mA to 80 mA/10 mA to 120 mA (Selectable by MODE Terminal) ( Current Value Setting for All Output Terminals Using External Resistor and Internal Brightness Control Register)
  • Constant Current Accuracy ±4% (Maximum Error Between Bits)
  • Voltage Applied to Constant Current Output Terminals:
    • Minimum 0.4 V (Output Current 5 mA to 40 mA)
    • Minimum 0.7 V (Output Current 40 mA to 80 mA)
  • 256 Gray Scale Display:
    • Pulse Width Control 256 Steps
  • Brightness Adjustment:
    • Output Current Adjustment for 32 Steps (Adjustment for Brightness Deviation Between LED Modules)
    • 8 Steps Brightness Control by 8 Times Speed Gray Scale Control Clock (Brightness Adjustment for Panel)
  • Error Output Signal Check:
    • Check Error Output Signal Line Such as Protection Circuit When Operating
  • Data Output Timing Selectable:
    • Select Data Output Timing for Shift Register Relative to Clock
  • OVM (Output Voltage Monitor):
    • Monitor Voltage on Constant Current Output Terminals (Detect LED Disconnection and Short Circuit)
  • WDT (Watchdog Timer):
    • Turn Output Off When Scan Signal Stopped
  • TSD (Thermal Shut Down):
    • Turn Output Off When Junction Temperature Exceeds Limit
  • Data Input:
    • Clock Synchronized 1 Bit Serial Input (Shmitt-Triggered Input)
  • Data Output:
    • Clock Synchronized 1 Bit Serial Output (3-State Output)
  • Input Signal Level:
    • CMOS Level
  • Power Supply Voltage...4.5 V to 5.5 V
  • Maximum Output Voltage...17 V
  • Data Transfer Rate...15 MHz (Max
  • Gray Scale Clock Frequency...8 MHz (Max)
  • Operating Free-Air Temperature Range
    -20°C to 85°C
  • 64-Pin HTQFP Package (PD = 4.9 W,
    TA = 25°C)
  • Drive Capability and Output Counts:
    • 80 mA (Current Sink) × 16 Bits
    • 120 mA (Current Sink) × 8 Bits
  • Constant Current Output Range:
    • 5 mA to 80 mA/10 mA to 120 mA (Selectable by MODE Terminal) ( Current Value Setting for All Output Terminals Using External Resistor and Internal Brightness Control Register)
  • Constant Current Accuracy ±4% (Maximum Error Between Bits)
  • Voltage Applied to Constant Current Output Terminals:
    • Minimum 0.4 V (Output Current 5 mA to 40 mA)
    • Minimum 0.7 V (Output Current 40 mA to 80 mA)
  • 256 Gray Scale Display:
    • Pulse Width Control 256 Steps
  • Brightness Adjustment:
    • Output Current Adjustment for 32 Steps (Adjustment for Brightness Deviation Between LED Modules)
    • 8 Steps Brightness Control by 8 Times Speed Gray Scale Control Clock (Brightness Adjustment for Panel)
  • Error Output Signal Check:
    • Check Error Output Signal Line Such as Protection Circuit When Operating
  • Data Output Timing Selectable:
    • Select Data Output Timing for Shift Register Relative to Clock
  • OVM (Output Voltage Monitor):
    • Monitor Voltage on Constant Current Output Terminals (Detect LED Disconnection and Short Circuit)
  • WDT (Watchdog Timer):
    • Turn Output Off When Scan Signal Stopped
  • TSD (Thermal Shut Down):
    • Turn Output Off When Junction Temperature Exceeds Limit
  • Data Input:
    • Clock Synchronized 1 Bit Serial Input (Shmitt-Triggered Input)
  • Data Output:
    • Clock Synchronized 1 Bit Serial Output (3-State Output)
  • Input Signal Level:
    • CMOS Level
  • Power Supply Voltage...4.5 V to 5.5 V
  • Maximum Output Voltage...17 V
  • Data Transfer Rate...15 MHz (Max
  • Gray Scale Clock Frequency...8 MHz (Max)
  • Operating Free-Air Temperature Range
    -20°C to 85°C
  • 64-Pin HTQFP Package (PD = 4.9 W,
    TA = 25°C)

The TLC5905 is a constant current driver that incorporates shift register, data latch, constant current circuitry with a current value adjustable and 256 gray scale display that uses pulse width control. The output current can be selected as maximum 80 mA with 16 bits or 120 mA with 8 bit. The current value of the constant current output is set by one external resistor. After this device is mounted on a printed-circuit board (PCB), the brightness deviation between LED modules (ICs) can be adjusted using an external data input, and the brightness control for the panel can be accomplished by the brightness adjustment circuitry. Also, the device incorporates the output voltage monitor (OVM) used for LED open detection (LOD) by monitoring constant current output. Moreover, the device incorporates watchdog timer (WDT) circuitry, which turns constant current output off when the scan signal stops during dynamic scanning operation, and thermal shutdown (TSD) circuitry, which turns constant current output off when the junction temperature exceeds the limit.

The TLC5905 is a constant current driver that incorporates shift register, data latch, constant current circuitry with a current value adjustable and 256 gray scale display that uses pulse width control. The output current can be selected as maximum 80 mA with 16 bits or 120 mA with 8 bit. The current value of the constant current output is set by one external resistor. After this device is mounted on a printed-circuit board (PCB), the brightness deviation between LED modules (ICs) can be adjusted using an external data input, and the brightness control for the panel can be accomplished by the brightness adjustment circuitry. Also, the device incorporates the output voltage monitor (OVM) used for LED open detection (LOD) by monitoring constant current output. Moreover, the device incorporates watchdog timer (WDT) circuitry, which turns constant current output off when the scan signal stops during dynamic scanning operation, and thermal shutdown (TSD) circuitry, which turns constant current output off when the junction temperature exceeds the limit.

filter Andere Treiber für LED-Displays suchen
Herunterladen Video mit Transkript ansehen Video

Technische Dokumentation

star =Von TI ausgewählte Top-Empfehlungen für dieses Produkt
Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.
Alle anzeigen 2
Typ Titel Datum
* Data sheet LED Driver datasheet 24 Nov 1999
White paper Common LED Functions and LED Driver Design Considerations 21 Sep 2020

Design und Entwicklung

Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.

Simulationstool

PSPICE-FOR-TI — PSpice® für TI Design-und Simulationstool

PSpice® für TI ist eine Design- und Simulationsumgebung, welche Sie dabei unterstützt, die Funktionalität analoger Schaltungen zu evaluieren. Diese voll ausgestattete Design- und Simulationssuite verwendet eine analoge Analyse-Engine von Cadence®. PSpice für TI ist kostenlos erhältlich und (...)
Anfordern
Gehäuse Pins CAD-Symbole, Footprints und 3D-Modelle
HTQFP (PAP) 64 Ultra Librarian
Es gelten die allgemeinen Geschäftsbedingungen von TI für Evaluierungsartikel.

Bestellen & Qualität

Beinhaltete Information:
  • RoHS
  • REACH
  • Bausteinkennzeichnung
  • Blei-Finish/Ball-Material
  • MSL-Rating / Spitzenrückfluss
  • MTBF-/FIT-Schätzungen
  • Materialinhalt
  • Qualifikationszusammenfassung
  • Kontinuierliches Zuverlässigkeitsmonitoring
Beinhaltete Information:
  • Werksstandort
  • Montagestandort

Support und Schulungen

TI E2E™-Foren mit technischem Support von TI-Ingenieuren

Alle Forenthemen auf Englisch anzeigen

Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.

Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support. ​​​​​​​​​​​​​​

Videos