Startseite Energiemanagement AC/DC- und DC/DC-Wandler (integrierter FET)
Startseite
Energiemanagement
AC/DC- und DC/DC-Wandler (integrierter FET)
NEU

TPS546E25

VORSCHAU

Stapelbarer synchroner PMBus-Abwärtswandler, 4 bis 18 V Eingangsspannung, 50 A

Jetzt bestellen
Datenblatt

TPS546E25

VORSCHAU
Datenblatt Jetzt bestellen

Produktdetails

Rating Catalog Operating temperature range (°C) -40 to 125 Topology Buck Type Converter Iout (max) (A) 50 Vin (min) (V) 4 Vin (max) (V) 18 Switching frequency (min) (kHz) 400 Switching frequency (max) (kHz) 2000 Features Adaptive/Dynamic Voltage Scaling, Adjustable current limit, Differential Remote Sense, Enable, Extended security, Forced PWM, Over Current Protection, PMBUS, Phase Interleaving, Power good, Pre-Bias Start-Up, Soft Start Adjustable, Synchronous Rectification, UVLO adjustable, Voltage Margining Control mode D-CAP4 Vout (min) (V) 0.4 Vout (max) (V) 5.5 Iq (typ) (µA) 7500 Duty cycle (max) (%) 85
Rating Catalog Operating temperature range (°C) -40 to 125 Topology Buck Type Converter Iout (max) (A) 50 Vin (min) (V) 4 Vin (max) (V) 18 Switching frequency (min) (kHz) 400 Switching frequency (max) (kHz) 2000 Features Adaptive/Dynamic Voltage Scaling, Adjustable current limit, Differential Remote Sense, Enable, Extended security, Forced PWM, Over Current Protection, PMBUS, Phase Interleaving, Power good, Pre-Bias Start-Up, Soft Start Adjustable, Synchronous Rectification, UVLO adjustable, Voltage Margining Control mode D-CAP4 Vout (min) (V) 0.4 Vout (max) (V) 5.5 Iq (typ) (µA) 7500 Duty cycle (max) (%) 85
WQFN-FCRLF (RXX) 37 30 mm² 6 x 5
  • 4V to 18V input voltage without external bias
  • 2.7V to 18V input voltage with external bias
  • 0.4V to 5.5V output voltage
  • Supports 50A single-phase or 2 ×, 3 ×, or 4 × stacked configurations
  • Rdson_HS = 2.9mΩ, Rdson_LS = 1mΩ
  • 400kHz to 2MHz operating frequency (four discrete settings through pinstrap, additional settings through PMBus)
  • PMBus programmability
    • Revision 1.5 Compliant with PASSKEY security feature
    • Input voltage, output voltage, output current, temperature telemetry
    • Programmable overcurrent, overvoltage, undervoltage, overtemperature protections
    • Includes single command write function in stacked configuration
    • Extended write protection feature
    • Non-volatile memory to store configuration settings

  • Two methods for programming the output voltage

    • Internal resistor divider (discrete settings), with boot-up voltage selected by pin strapping
    • External resistor divider (continuous settings), with boot-up voltage selected by VBOOT field
  • Precision voltage reference and differential remote sense for high output accuracy
    • +/– 0.5% DAC accuracy from 0°C to 85°C junction
    • +/– 1% VOUT tolerance from –40°C to 125°C junction
  • Selectable FCCM/DCM in single phase only
  • Start-up without PMBus communication through pin strapping
  • Safe start-up into prebiased output
  • Programmable soft-start time from 0.5ms to 16ms
  • Programmable soft-stop time from 0.5ms to 4ms
  • D-CAP4 control topology with fast transient response, supporting all ceramic output capacitors
  • Programmable internal loop compensation
  • Selectable cycle-by-cycle valley current limit
  • Open-drain power-good output
  • 4V to 18V input voltage without external bias
  • 2.7V to 18V input voltage with external bias
  • 0.4V to 5.5V output voltage
  • Supports 50A single-phase or 2 ×, 3 ×, or 4 × stacked configurations
  • Rdson_HS = 2.9mΩ, Rdson_LS = 1mΩ
  • 400kHz to 2MHz operating frequency (four discrete settings through pinstrap, additional settings through PMBus)
  • PMBus programmability
    • Revision 1.5 Compliant with PASSKEY security feature
    • Input voltage, output voltage, output current, temperature telemetry
    • Programmable overcurrent, overvoltage, undervoltage, overtemperature protections
    • Includes single command write function in stacked configuration
    • Extended write protection feature
    • Non-volatile memory to store configuration settings

  • Two methods for programming the output voltage

    • Internal resistor divider (discrete settings), with boot-up voltage selected by pin strapping
    • External resistor divider (continuous settings), with boot-up voltage selected by VBOOT field
  • Precision voltage reference and differential remote sense for high output accuracy
    • +/– 0.5% DAC accuracy from 0°C to 85°C junction
    • +/– 1% VOUT tolerance from –40°C to 125°C junction
  • Selectable FCCM/DCM in single phase only
  • Start-up without PMBus communication through pin strapping
  • Safe start-up into prebiased output
  • Programmable soft-start time from 0.5ms to 16ms
  • Programmable soft-stop time from 0.5ms to 4ms
  • D-CAP4 control topology with fast transient response, supporting all ceramic output capacitors
  • Programmable internal loop compensation
  • Selectable cycle-by-cycle valley current limit
  • Open-drain power-good output

The TPS546E25 device is a highly integrated, buck converter with D-CAP4 control topology for fast transient response. All programmable parameters can be configured by the PMBus interface and stored in NVM as the new default values to minimize the external component count. Pinstrap options allow for configuration as primary or secondary, stack position and stack number, DCM (single phase only) or FCCM, overcurrent limit, fault response, internal or external feedback resistor, output voltage selection or range, switching frequency, and compensation.

The PMBus interface with 1MHz clock support gives a convenient, standardized digital interface for configuration as well as telemetry of key parameters including output voltage, output current, and internal die temperature. Response to fault conditions can be set to restart, latch off, or ignore, depending on system requirements. Two, three, and four TPS546E25 devices can be interconnected to provide up to 200A on a single output.

The device has an option to overdrive the internal 5V LDO with an external 5V supply through the VDRV and VCC pins to improve efficiency, reduce power dissipation, and enable start-up with a lower input voltage.

The TPS546E25 is a lead-free device and is RoHS compliant without exemption.

The TPS546E25 device is a highly integrated, buck converter with D-CAP4 control topology for fast transient response. All programmable parameters can be configured by the PMBus interface and stored in NVM as the new default values to minimize the external component count. Pinstrap options allow for configuration as primary or secondary, stack position and stack number, DCM (single phase only) or FCCM, overcurrent limit, fault response, internal or external feedback resistor, output voltage selection or range, switching frequency, and compensation.

The PMBus interface with 1MHz clock support gives a convenient, standardized digital interface for configuration as well as telemetry of key parameters including output voltage, output current, and internal die temperature. Response to fault conditions can be set to restart, latch off, or ignore, depending on system requirements. Two, three, and four TPS546E25 devices can be interconnected to provide up to 200A on a single output.

The device has an option to overdrive the internal 5V LDO with an external 5V supply through the VDRV and VCC pins to improve efficiency, reduce power dissipation, and enable start-up with a lower input voltage.

The TPS546E25 is a lead-free device and is RoHS compliant without exemption.
filter Andere AC/DC- und DC/DC-Wandler (integrierter FET) suchen
Herunterladen Video mit Transkript ansehen Video

Technische Dokumentation

star =Von TI ausgewählte Top-Empfehlungen für dieses Produkt
Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.
Alle anzeigen 5
Typ Titel Datum
* Data sheet TPS546E25 4V to 18V Input, 50A , 4 × Stackable, Synchronous Buck Converter With PMBus and Telemetry datasheet PDF | HTML 12 Jul 2024
Application note Point-of-Load Designs in Data Center Applications for Intel Xeon Sapphire Rapids Scalable Processors (Rev. C) PDF | HTML 09 Okt 2024
Application note TPS546E25 and TPS546C25 Advanced Product Errata PDF | HTML 31 Jul 2024
EVM User's guide TPS546E25EVM-1PH SWIFT™ Step-Down Converter Evaluation Module PDF | HTML 15 Jul 2024
Certificate TPS546E25EVM-1PH EU Declaration of Conformity (DoC) (Rev. A) 09 Jul 2024

Design und Entwicklung

Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.

Evaluierungsplatine

TPS546E25EVM-1PH — Einphasiges Evaluierungsmodul TPS546E25

Das Evaluierungsmodul (EVM) TPS546E25 ist ein einphasiges Abwärtsdesign unter Verwendung des Bausteins TPS546E25. Das Evaluierungsmodul ist für einen nominalen 12 V-Bus ausgelegt und erzeugt einen geregelten 1,2 V-Ausgang bei bis zu 50 A-Laststrom. Das TPS546E25EVM-1PH wurde entwickelt, um den (...)

Benutzerhandbuch: PDF | HTML
Nicht verfügbar auf TI.com
Evaluierungsplatine

USB-TO-GPIO2 — Evaluierungsmodul (EVM) für USB-TO-GPIO2-Schnittstellenadapter

Dieses EVM dient als Schnittstellenadapter bzw. Brücke zwischen einem Host-PC und einem oder mehreren Ziel-Geräten über ein standardmäßiges USB-Typ-A-/Mini-B-Kabel. Die Kommunikation zwischen dem USB-Schnittstellenadapter und dem Host-PC erfolgt über USB. Die Kommunikation zwischen dem (...)
Benutzerhandbuch: PDF | HTML
Nicht verfügbar auf TI.com
Designtool

TPS546E25-DESIGN — TPS546E25 Design file

Design files for TPS546E25
Unterstützte Produkte und Hardware

Unterstützte Produkte und Hardware

Produkte
AC/DC- und DC/DC-Wandler (integrierter FET)
TPS546C25 — Stapelbarer synchroner PMBus-Abwärtswandler, 4 V- bis 18 V-Eingangsspannung, 35 A TPS546E25 — Stapelbarer synchroner PMBus-Abwärtswandler, 4 bis 18 V Eingangsspannung, 50 A
Download-Optionen
Gehäuse Pins CAD-Symbole, Footprints und 3D-Modelle
WQFN-FCRLF (RXX) 37 Ultra Librarian
Es gelten die allgemeinen Geschäftsbedingungen von TI für Evaluierungsartikel.

Bestellen & Qualität

Beinhaltete Information:
  • RoHS
  • REACH
  • Bausteinkennzeichnung
  • Blei-Finish/Ball-Material
  • MSL-Rating / Spitzenrückfluss
  • MTBF-/FIT-Schätzungen
  • Materialinhalt
  • Qualifikationszusammenfassung
  • Kontinuierliches Zuverlässigkeitsmonitoring
Beinhaltete Information:
  • Werksstandort
  • Montagestandort

Support und Schulungen

TI E2E™-Foren mit technischem Support von TI-Ingenieuren

Alle Forenthemen auf Englisch anzeigen

Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.

Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support. ​​​​​​​​​​​​​​

Videos