首頁 電源管理 LED 驅動器 背光 LED 驅動器
首頁
電源管理
LED 驅動器
背光 LED 驅動器

TPS61160

現行

採用 2mm x 2mm 封裝且具數位和 PWM 亮度控制的白光 LED 驅動器

立即訂購
產品規格表

TPS61160

現行
產品規格表 立即訂購

產品詳細資料

Number of channels 1 Vin (min) (V) 2.7 Vin (max) (V) 18 Vout (min) (V) 2.7 Vout (max) (V) 26 Type Inductive Switching frequency (max) (kHz) 600 Duty cycle (max) (%) 93 LED current per channel (mA) 20 Peak efficiency (%) 90 Topology Boost Features EasyScale 1-Wire Interface, Load Disconnect During Shutdown Operating temperature range (°C) -40 to 85 Rating Catalog
Number of channels 1 Vin (min) (V) 2.7 Vin (max) (V) 18 Vout (min) (V) 2.7 Vout (max) (V) 26 Type Inductive Switching frequency (max) (kHz) 600 Duty cycle (max) (%) 93 LED current per channel (mA) 20 Peak efficiency (%) 90 Topology Boost Features EasyScale 1-Wire Interface, Load Disconnect During Shutdown Operating temperature range (°C) -40 to 85 Rating Catalog
WSON (DRV) 6 4 mm² 2 x 2
  • 2.7-V to 18-V Input Voltage Range
  • 26-V Open LED Protection (TPS61160)
  • 38-V Open LED Protection (TPS61161)
  • 200-mV Reference Voltage With ±2% Accuracy
  • Flexible Digital and PWM Brightness Control
  • Built-in Soft Start
  • Up to 90% Efficiency
  • 2.7-V to 18-V Input Voltage Range
  • 26-V Open LED Protection (TPS61160)
  • 38-V Open LED Protection (TPS61161)
  • 200-mV Reference Voltage With ±2% Accuracy
  • Flexible Digital and PWM Brightness Control
  • Built-in Soft Start
  • Up to 90% Efficiency

With a 40-V rated integrated switch FET, the TPS61160 and TPS61161 are boost converters that drive LEDs in series. The boost converters run at 600-kHz fixed switching frequency to reduce output ripple, improve conversion efficiency, and allow for the use of small external components.

The default white LED current is set with the external sensor resistor RSET, and the feedback voltage is regulated to 200 mV, as shown in the . During the operation, the LED current can be controlled using the one-wire digital interface (EasyScale protocol) through the CTRL pin. Alternatively, a pulse width modulation (PWM) signal can be applied to the CTRL pin through which the duty cycle determines the feedback reference voltage. In either digital or PWM mode, the TPS61160 and TPS61161 do not burst the LED current; therefore, they do not generate audible noises on the output capacitor. For maximum protection, the device features integrated open LED protection that disable the TPS61160 and/or TPS61161 to prevent the output voltage from exceeding the device's absolute maximum voltage ratings during open LED conditions.

The TPS61160 and TPS61161 are available in a space-saving, 2-mm × 2-mm WSON package with thermal pad.

For all available packages, see the orderable addendum at the end of the data sheet.

With a 40-V rated integrated switch FET, the TPS61160 and TPS61161 are boost converters that drive LEDs in series. The boost converters run at 600-kHz fixed switching frequency to reduce output ripple, improve conversion efficiency, and allow for the use of small external components.

The default white LED current is set with the external sensor resistor RSET, and the feedback voltage is regulated to 200 mV, as shown in the . During the operation, the LED current can be controlled using the one-wire digital interface (EasyScale protocol) through the CTRL pin. Alternatively, a pulse width modulation (PWM) signal can be applied to the CTRL pin through which the duty cycle determines the feedback reference voltage. In either digital or PWM mode, the TPS61160 and TPS61161 do not burst the LED current; therefore, they do not generate audible noises on the output capacitor. For maximum protection, the device features integrated open LED protection that disable the TPS61160 and/or TPS61161 to prevent the output voltage from exceeding the device's absolute maximum voltage ratings during open LED conditions.

The TPS61160 and TPS61161 are available in a space-saving, 2-mm × 2-mm WSON package with thermal pad.

For all available packages, see the orderable addendum at the end of the data sheet.
filter 尋找其它 背光 LED 驅動器
下載 觀看有字幕稿的影片 影片

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 12
類型 標題 日期
* Data sheet TPS6116x White LED Drivers With Digital and PWM Brightness Control in 2-mm x 2-mm WSON Package datasheet (Rev. E) PDF | HTML 2016年 7月 14日
White paper Common LED Functions and LED Driver Design Considerations 2020年 9月 21日
Application note Some Guidelines and Tips for the LED Driver Application 2019年 8月 14日
Application note Performing Accurate PFM Mode Efficiency Measurements (Rev. A) 2018年 12月 11日
Selection guide Power Management Guide 2018 (Rev. R) 2018年 6月 25日
Application note Optimizing Transient Response of Internally Compensated DC-DC Converters (Rev. B) 2017年 11月 29日
Application note Extending the Soft Start Time Without a Soft Start Pin (Rev. B) 2017年 6月 15日
Application note Analog PWM Dimming in White-LED Drivers 2016年 12月 21日
Application note Inductor Selection in Boost Converters for LCD Backlight Applications 2016年 10月 24日
Application note Schottky Diode Selection in Asynchronous Boost Converters 2016年 9月 6日
EVM User's guide TPS61161EVM-243 (Rev. D) 2013年 5月 7日
Application note How to Use Analog Dimming With TPS6116x 2011年 8月 5日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TPS61160EVM-243 — TPS61160EVM-243 評估模組

The TPS61160EVM-243 demonstrates the TPS61160 White LED Driver with Digital and PWM Brightness Control. With a 40-V rated integrated switch FET, the TPS61160 is a boost converter that drives up to 10 LEDs in series.
使用指南: PDF
TI.com 無法提供
支援軟體

TPS6116XEVM-SW — TPS6116x 評估模組的軟體

The TPS6116xEVM-SW software provides a software interface for the TPS6116x/70 EVM boards. Use this software to change the TPS6116x IC register via the USB Interface Adapter.
下載選項
計算工具

SLVC366 — Design Tool for Analog Dimming Using a PWM Signal

支援產品和硬體

支援產品和硬體

產品
汽車 LED 驅動器
TPS61161-Q1 — 採用 2mm x 2mm QFN 封裝且具數位和 PWM 亮度控制的車用白光 LED 驅動器
背光 LED 驅動器
TPS61160 — 採用 2mm x 2mm 封裝且具數位和 PWM 亮度控制的白光 LED 驅動器 TPS61160A — 採用 2mm x 2mm 封裝，具 PWM 亮度控制的白色 LED 驅動器。最多可串聯 10 個 LED TPS61161 — 採用 2mm x 2mm WSON 封裝且具數位和 PWM 亮度控制的白光 LED 驅動器 TPS61165 — 2mm x 2mm QFN 封裝的高亮度白光 LED 驅動器 TPS61166 — 含整合式電源二極體和快速脈衝調光模式的白光 LED 驅動器
AC/DC 和 DC/DC 轉換器 (整合式 FET)
TLV62130A — 採用 3x3 QFN 封裝且具備 DCS-Control 的 3-17V 3A 降壓式轉換器 TLV62150A — 採用 3x3 QFN 封裝且具 DCS 控制的 4-17V、1A 降壓轉換器 TPS62130 — 採用 3x3 QFN 封裝且具備 DCS-Control 的 3-17V 3A 降壓式轉換器 TPS62130A — 採用 3x3 QFN 封裝的 3V 至 17V 3-A 降壓轉換器 TPS62140 — 採用 3x3 QFN 封裝且具備 DCS-Control 的 3–17V 2A 降壓式轉換器 TPS62140A — 採用 3x3 QFN 封裝且具備 DCS-Control 的 3–17V 2A 降壓式轉換器 TPS62150 — 採用 3x3 QFN 封裝且具備 DCS-Control 的 3–17V 1A 降壓式轉換器 TPS62150A — 採用 3x3 QFN 封裝且具備 DCS 控制的3-17V 1A 3MHz 降壓轉換器
下載
Gerber 檔案

TPS6116xEVM Gerber Files

SLVC152.ZIP (101 KB)
下載
模擬工具

PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具

PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
要求
封裝 針腳 CAD 符號、佔位空間與 3D 模型
WSON (DRV) 6 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片