韌體
TUSB9261-Q1
- Qualified for Automotive Applications
- AEC-Q100 Qualified with the Following Exceptions:
- Device CDM ESD Classification Level C3
- Ideal for bridging Serial ATA (SATA) Devices, Such
as Hard Disk Drives (HDD), Solid State Drives (SSD),
or Optical Drives (OD) to Universal Serial Bus (USB) - USB Interface
- Integrated Transceiver Supports SS/HS/FS Signaling
- Best in Class Adaptive Equalizer
- Allows for Greater Jitter Tolerance in the Receiver
- USB Class Support
- USB Attached SCSI Protocol (UASP) for HDD and SSD
- USB Mass Storage Class Bulk-Only Transport (BOT)
Including Support for Error Conditions Per the
13 Cases (Defined in the BOT Specification) - USB Bootability Support
- USB Human Interface Device (HID)
- Supports Firmware Update Via USB Using a TI Provided Application
- SATA Interface
- Serial ATA Specification Revision 2.6 Supporting gen1 and
gen2 Data Rates - Supports hot plug
- Supports Mass-Storage Devices Compatible with the ATA/ATAPI-8
Specification
- Serial ATA Specification Revision 2.6 Supporting gen1 and
- Integrated ARM Cortex M3 Core
- Customizable Application Code Loaded From EEPROM Via SPI Interface
- Two Additional SPI Port Chip Selects for Peripheral Connection
- Up to 5 GPIOs for End-User Configuration via HID
- Serial Communications Interface for Debug (UART)
- General Features
- Integrated Spread Spectrum Clock Generation Enables Operation
from a Single Low Cost Crystal or Clock Oscillator- Supports 20, 25, 30 or 40 MHz
- JTAG Interface for IEEE1149.1 and IEEE1149.6 Boundary Scan
- Available in a Fully RoHS Compliant Package (PAP)
- Integrated Spread Spectrum Clock Generation Enables Operation
The TUSB9261-Q1 is an ARM cortex M3 microcontroller based Universal Serial Bus (USB) 3.0 to Serial ATA (SATA) bridge. It provides the necessary hardware and firmware to implement a USB Attached SCSI Protocol (UASP) compliant mass storage device suitable for bridging SATA compatible hard disk drives (HDD) and solid state disk drives (SSD) to a USB 3.0 bus. The firmware also implements the mass storage class bulk-only transport (BOT) for bridging optical drives and other compatible SATA devices to the USB bus. In addition to UASP and BOT support,a USB human interface device (HID) interfaces is supported for control of the general purpose input/ouput (GPIO). The SATA interface supports gen1 (1.5-Gbps) and gen2 (3.0-Gbps) for cable lengths up to 2 meters.
The device is available in a 64-pin HTQFP package and is designed for operation over the industrial temperature range of –40°C to 85°C.
技術文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 6 | 類型 | 標題 | 日期 | ||
|---|---|---|---|---|
| * | Data sheet | TUSB9261-Q1 USB 3.0 to SATA Bridge datasheet (Rev. A) | 2014年 1月 31日 | |
| * | Errata | TUSB9261 Errata (Rev. B) | 2012年 12月 20日 | |
| User guide | TUSB9261 DEMO User's Guide (Rev. A) | 2014年 12月 9日 | ||
| Application note | TUSB9261 Implementation Guide (Rev. E) | 2014年 12月 9日 | ||
| User guide | TUSB9260 Flash Burner - User Guide (Rev. D) | 2013年 10月 24日 | ||
| User guide | TUSB926x SpeedBoost Monitor User's Guide | 2010年 9月 23日 |
設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
開發板
TUSB9261DEMO — TUSB9261 展示套件
The TUSB9261DEMO board is a bridge between a SuperSpeed USB (USB 3.0) bus and a Serial–ATA (SATA) development kit. The TUSB9261DEMO is used to evaluate system compatibility. It provides a TUSB9261 hardware for connection to a SATA device such as a solid state drive, hard disk drive, DVD (...)
軟體程式設計工具
SLLC414 — TUSB926x FlashBurner Utility
支援產品和硬體
產品
USB 集線器與控制器
模擬工具
PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具
PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
模擬工具
TINA-TI — 基於 SPICE 的類比模擬程式
TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
使用指南: PDF
參考設計
TIDA-00148 — 適用於車載資訊娛樂系統的 USB 2.0/3.0 大量儲存橋接器
This TIDA-00148 reference design features the TUSB9261DEMO which allows quick evaluation of system compatibility for connections to SATA devices used for automotive infotainment systems. The firmware used in TIDA-00148 is capable of supporting a single SATA drive such as a solid state drive, hard (...)
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| HTQFP (PAP) | 64 | Ultra Librarian |
訂購與品質
內含資訊：
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 認證摘要
- 進行中持續性的可靠性監測
內含資訊：
- 晶圓廠位置
- 組裝地點
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。