Startseite Energiemanagement LED-Treiber Kfz-LED-Treiber
Startseite
Energiemanagement
LED-Treiber
Kfz-LED-Treiber

TPS929240-Q1

AKTIV

24-Kanal-/40-V-High-Side-LED-und-OLED-Treiber für die Automobilindustrie

Jetzt bestellen
Datenblatt

TPS929240-Q1

AKTIV
Datenblatt Jetzt bestellen

Produktdetails

Number of channels 24 Topology Current Source Rating Automotive TI functional safety category Functional Safety-Capable Operating temperature range (°C) -40 to 125 Vin (min) (V) 4.5 Vin (max) (V) 40 Vout (min) (V) 0 Vout (max) (V) 40 Iout (max) (A) 0.1 Iq (typ) (mA) 10 Features Enable/Shutdown, Fault Detection, Fault Diagnostic, LED Open Detection, LED Short Detection, Precise dimming control, Thermal shutdown
Number of channels 24 Topology Current Source Rating Automotive TI functional safety category Functional Safety-Capable Operating temperature range (°C) -40 to 125 Vin (min) (V) 4.5 Vin (max) (V) 40 Vout (min) (V) 0 Vout (max) (V) 40 Iout (max) (A) 0.1 Iq (typ) (mA) 10 Features Enable/Shutdown, Fault Detection, Fault Diagnostic, LED Open Detection, LED Short Detection, Precise dimming control, Thermal shutdown
HTSSOP (DCP) 38 62.08 mm² 9.7 x 6.4
  • AEC-Q100 qualified for automotive applications:
    • Temperature grade 1: –40°C to +125°C, TA
  • 24-channel precision high-side current output:
    • Device supply voltage 4.5V to 40V
    • LED supply voltage 4V to 36V
    • Up to 100mA channel current set by resistor
    • 2-bit global, 6-bit independent current setting
    • High-current accuracy < ±5% at 5mA to 100mA
    • Low voltage drop 750mV at 100mA
    • 12-bit independent PWM dimming
    • Programmable PWM frequency up to 20kHz
    • Phase-shift PWM dimming
    • Linear and exponential dimming method
  • FlexWire™ control interface
    • Up to 1MHz clock frequency
    • Maximum 16 devices on one FlexWire bus
    • Up to 24 bytes data transaction in one frame
    • 5V LDO output to supply CAN transceiver
  • Diagnostic and protection:
    • Programmable FAIL-SAFE state
    • LED open-circuit detection
    • LED short-circuit detection
    • Single-LED short-circuit diagnostic
    • Programmable low-supply detection
    • Open-drain ERR for fault indication
    • Watchdog and CRC for FlexWire interface
    • 8-bit ADC for pin voltage measurement
    • Overtemperature protection
  • AEC-Q100 qualified for automotive applications:
    • Temperature grade 1: –40°C to +125°C, TA
  • 24-channel precision high-side current output:
    • Device supply voltage 4.5V to 40V
    • LED supply voltage 4V to 36V
    • Up to 100mA channel current set by resistor
    • 2-bit global, 6-bit independent current setting
    • High-current accuracy < ±5% at 5mA to 100mA
    • Low voltage drop 750mV at 100mA
    • 12-bit independent PWM dimming
    • Programmable PWM frequency up to 20kHz
    • Phase-shift PWM dimming
    • Linear and exponential dimming method
  • FlexWire™ control interface
    • Up to 1MHz clock frequency
    • Maximum 16 devices on one FlexWire bus
    • Up to 24 bytes data transaction in one frame
    • 5V LDO output to supply CAN transceiver
  • Diagnostic and protection:
    • Programmable FAIL-SAFE state
    • LED open-circuit detection
    • LED short-circuit detection
    • Single-LED short-circuit diagnostic
    • Programmable low-supply detection
    • Open-drain ERR for fault indication
    • Watchdog and CRC for FlexWire interface
    • 8-bit ADC for pin voltage measurement
    • Overtemperature protection

With the increasing demand for animation in automotive lighting, LEDs must be controlled independently. Therefore, LED drivers with digital interfaces are essential to effectively drive pixel-controlled lighting applications. In exterior lighting, multiple lamp functions are typically located on different PCB boards with off-board wires connected to each other. It is difficult for a traditional single-ended interface to meet the strict EMC requirements. By using an industrial-standard CAN physical layer, the UART-based FlexWire interface of the TPS929240-Q1 easily accomplishes long distance off-board communication without impacting EMC.

The TPS929240-Q1 is a 24-channel, 40V high-side LED driver that controls the 8-bit output current and 12-bit PWM duty cycles. The device meets multiple regulation requirements with LED open-circuit, short-to-ground, and single LED short-circuit diagnostics. A configurable watchdog also automatically sets FAIL-SAFE states when the MCU connection is lost, and, with programmable EEPROM, TPS929240-Q1 can flexibly be set for different application scenarios.

With the increasing demand for animation in automotive lighting, LEDs must be controlled independently. Therefore, LED drivers with digital interfaces are essential to effectively drive pixel-controlled lighting applications. In exterior lighting, multiple lamp functions are typically located on different PCB boards with off-board wires connected to each other. It is difficult for a traditional single-ended interface to meet the strict EMC requirements. By using an industrial-standard CAN physical layer, the UART-based FlexWire interface of the TPS929240-Q1 easily accomplishes long distance off-board communication without impacting EMC.

The TPS929240-Q1 is a 24-channel, 40V high-side LED driver that controls the 8-bit output current and 12-bit PWM duty cycles. The device meets multiple regulation requirements with LED open-circuit, short-to-ground, and single LED short-circuit diagnostics. A configurable watchdog also automatically sets FAIL-SAFE states when the MCU connection is lost, and, with programmable EEPROM, TPS929240-Q1 can flexibly be set for different application scenarios.
filter Andere Kfz-LED-Treiber suchen
Herunterladen Video mit Transkript ansehen Video

Technische Dokumentation

star =Von TI ausgewählte Top-Empfehlungen für dieses Produkt
Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.
Alle anzeigen 3
Typ Titel Datum
* Data sheet TPS929240-Q1 24-Channel, Automotive, 40V, High-Side (O)LED Driver With FlexWire™ Interface datasheet (Rev. B) PDF | HTML 16 Apr 2024
User guide TPS929xxx-Q1 Sample Code User's Guide PDF | HTML 10 Apr 2023
Application note Typical Application to Achieve High Immunity to BCI PDF | HTML 07 Nov 2022

Design und Entwicklung

Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.

Evaluierungsplatine

TPS929240EVM — TPS929240-Q1-Evaluierungsmodul für 24-kanaligen LED-Treiber für die Automobilindustrie

Das Evaluierungsmodul (EVM) TPS929240-Q1 unterstützt Entwickler bei der Evaluierung des Betriebs und der Leistung von TPS929240-Q1, einem 12-kanaligen 40-V-Highside-LED-Treiber mit FLEXLED™-Schnittstelle zur individuellen Steuerung von Ausgangsstrom und PWM-Dutycycle für Beleuchtungsanwendungen im (...)

Benutzerhandbuch: PDF | HTML
Nicht verfügbar auf TI.com
Anwendungssoftware und Frameworks

TPS929240Q1-F5529-SW — TPS929240-Q1 reference code based on MSP430F5529 (MSP-EXP430F5529LP)

This reference code showcases the ability of the MSP430F5529 device to communicate with the TPS929240-Q1 LED driver. The code configures the MCU using UART to drive 24 LEDs which is available on the TPS929240EVM.
Unterstützte Produkte und Hardware

Unterstützte Produkte und Hardware

Produkte
Kfz-LED-Treiber
TPS929240-Q1 — 24-Kanal-/40-V-High-Side-LED-und-OLED-Treiber für die Automobilindustrie
Download-Optionen
Berechnungstool

SLVRBM1 — TPS929240-Q1 TPS929160-Q1 EEPROM Configuration Tool

Unterstützte Produkte und Hardware

Unterstützte Produkte und Hardware

Produkte
Kfz-LED-Treiber
TPS929160-Q1 — 16-Kanal-/40-V-High-Side-LED-und-OLED-Treiber für die Automobilindustrie TPS929240-Q1 — 24-Kanal-/40-V-High-Side-LED-und-OLED-Treiber für die Automobilindustrie
Herunterladen
Simulationstool

PSPICE-FOR-TI — PSpice® für TI Design-und Simulationstool

PSpice® für TI ist eine Design- und Simulationsumgebung, welche Sie dabei unterstützt, die Funktionalität analoger Schaltungen zu evaluieren. Diese voll ausgestattete Design- und Simulationssuite verwendet eine analoge Analyse-Engine von Cadence®. PSpice für TI ist kostenlos erhältlich und (...)
Anfordern
Gehäuse Pins CAD-Symbole, Footprints und 3D-Modelle
HTSSOP (DCP) 38 Ultra Librarian
Es gelten die allgemeinen Geschäftsbedingungen von TI für Evaluierungsartikel.

Bestellen & Qualität

Beinhaltete Information:
  • RoHS
  • REACH
  • Bausteinkennzeichnung
  • Blei-Finish/Ball-Material
  • MSL-Rating / Spitzenrückfluss
  • MTBF-/FIT-Schätzungen
  • Materialinhalt
  • Qualifikationszusammenfassung
  • Kontinuierliches Zuverlässigkeitsmonitoring
Beinhaltete Information:
  • Werksstandort
  • Montagestandort

Empfohlene Produkte können Parameter, Evaluierungsmodule oder Referenzdesigns zu diesem TI-Produkt beinhalten.

Support und Schulungen

TI E2E™-Foren mit technischem Support von TI-Ingenieuren

Alle Forenthemen auf Englisch anzeigen

Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.

Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support. ​​​​​​​​​​​​​​

Videos