TPS22949
- Integrated Current Limiter
- Input Voltage Range: 1.62 V to 4.5 V
- Low ON-Resistance
- rON = 300-mΩ at VIN = 4.5 V
- rON = 350-mΩ at VIN = 3.3 V
- rON = 400-mΩ at VIN = 2.5 V
- rON = 600-mΩ at VIN = 1.8 V
- Integrated 100-mA Minimum Current Limit
- Undervoltage Lockout
- Fast-Current Limit Response Time
- Integrated Fault Blanking and Auto Restart
- Stable Without Current Limiter Output Capacitor
(TPS22949A Only) - Integrated Low-Noise RF LDO
- Input Voltage Range: 1.62 V to 4.5 V
- Low Noise: 50 µVrms (10 Hz to 100 kHz)
- 80-dB VIN PSRR (10 Hz to 10 kHz)
- Fast Start-Up Time: 130 µs
- Low Dropout 100 mV at Iload =100 mA
- Integrated Output Discharge
- Stable With 2.2-µF Output Capacitor
- 1.8-V Compatible Control Input Threshold
- ESD Performance Tested Per JESD 22
- 3500 V Human Body Model
(A114-B, Class II) - 1000 V Charged Device Model
(C101)
- 3500 V Human Body Model
- Tiny 8-Terminal YZP Package (1.9 mm × 0.9 mm,
0.5-mm Pitch, 0.5-mm Height) and WSON-8
(DRG) 3.0 mm × 3.0 mm
The TPS22949 and TPS22949A are devices that provide protection to systems and loads in high-current conditions. The device contains a 500-mΩ current-limited P-channel MOSFET that can operate over an input voltage range of 1.62 V to 4.5 V as well as a low-dropout (LDO) regulator with a fixed output voltage of 1.8 V.
The switch is controlled by an on/off input (EN1), which can interface directly with low-voltage control signals. When the switch current reaches the maximum limit, the TPS22949/TPS22949A operates in a constant-current mode to prohibit excessive currents from causing damage. If the constant current condition persists after 12 ms, these devices shut off the switch and pull the fault signal pin (OC) low. The TPS22949/TPS22949A has an auto-restart feature that turns the switch on again after 70 ms if the EN1 pin is still active.
The output of the current limiter is internally connected to an RF low-dropout (LDO) regulator that offers good AC performance with very low ground current, good power supply rejection ratio (PSRR), low noise, fast start-up, and excellent line and load transient response. The output of the regulator is stable with ceramic capacitors. This LDO uses a precision voltage reference and feedback loop to achieve overall accuracy of 2% over all load, line, process, and temperature variations.
The TPS22949A integrates additional internal circuitry that increases the current limit of the switch during the power-up sequence. This feature allows the TPS22949A to operate without a storage capacitor at the input of the LDO.
The TPS22949 and TPS22949A are available in a space-saving 8-terminal WCSP (YZP) or in an 8-pin WSON package (DRG). Both devices are characterized for operation over the free-air temperature range of –40°C to 85°C.
기술 자료
| 유형 | 직함 | 날짜 | ||
|---|---|---|---|---|
| * | Data sheet | TPS22949x Current-Limited Load Switch With Low Noise Regulation Capability datasheet (Rev. D) | PDF | HTML | 2015/06/30 |
| Application note | Load Switch Thermal Considerations (Rev. A) | 2018/10/11 | ||
| Application note | Basics of Load Switches (Rev. A) | 2018/09/05 | ||
| Selection guide | Power Management Guide 2018 (Rev. R) | 2018/06/25 | ||
| Application note | Selecting a Load Switch to Replace a Discrete Solution | 2017/04/30 | ||
| Application note | Timing of Load Switches | 2017/04/27 | ||
| Application note | Managing Inrush Current (Rev. A) | 2015/05/28 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| WSON (DRG) | 8 | Ultra Librarian |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치