韌體
TMAG3001-CODE-EXAMPLE — TMAG3001 code example
Code examples will provide customers ease of use in developing firmware for the TMAG3001
TMAG3001
- Configurable power modes including:
- 2.1mA active mode current
- 0.45µA wake-up and sleep mode current
- 40nA sleep mode current
- Selectable linear magnetic range at X, Y, or Z axis:
- TMAG3001A1 sample: ±40mT, ±80mT
- TMAG3001A2: ±120mT, ±240mT
- Integrated angle calculation with gain and offset adjustment to support off-axis placement
- Conversion trigger by I2C or dedicated INT pin
- Interrupt signal based on
- Magnetic or Angle threshold crossing
- Change from previous measurement
- Configurable 3D or angle switch mode
- Optimized for low noise, supporting up to 20kSPS single axis conversion rate
- I2C interface with cyclic redundancy check (CRC):
- Maximum 1MHz I2C clock speed
-
ADDR pin enables four devices on the same bus
- Integrated temperature compensation to support multiple magnet types
- Built-in temperature sensor
- 1.65V to 3.6V supply voltage VCC range
- Operating temperature range: –40°C to 125°C
The TMAG3001 is a low-power linear 3D Hall-effect sensor designed for a wide range of industrial and personal electronics applications. This device integrates three independent Hall-effect sensors in the X, Y, and Z axes. A precision analog signal-chain along with an integrated 12-bit ADC digitizes the measured analog magnetic field values. The I2C interface, while supporting multiple operating VCC ranges, allows seamless data communication with low-voltage microcontrollers.
The TMAG3001 can be configured through the I2C interface to enable any combination of magnetic axes and temperature measurements. Additionally, the device can be configured to various power options (including wake-up and sleep mode) allowing designers to optimize system power consumption based on their system-level needs. Multiple sensor conversion schemes and I2C read frames help optimize throughput and accuracy. A dedicated INT pin can act as a system interrupt during low power wake-up and sleep mode, and can also be used by a microcontroller to trigger a new sensor conversion. The device also features a configurable low power switch mode for magnetic or angle measurements.
An integrated angle calculation engine (CORDIC) provides full 360° angular position information for both on-axis and off-axis angle measurement topologies. The angle calculation is performed using two user-selected magnetic axes. The device features magnetic gain and offset correction to mitigate the impact of system mechanical error sources.
The TMAG3001 features an ADDR pin that can be used to have four different I2C addresses. Each orderable part can be configured to select one of two magnetic field ranges that suits the magnet strength and component placement during system calibration.
The device performs consistently across a wide ambient temperature range of –40°C to 125°C.
您可能會感興趣的類似產品
功能相同，但引腳輸出與所比較的裝置不同
技術文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 9 | 類型 | 標題 | 日期 | ||
|---|---|---|---|---|
| * | Data sheet | TMAG3001 Low-Power 3D Linear and Angle Hall-Effect Sensor With I2 C Interface and Wake Up Detection in WCSP datasheet (Rev. B) | PDF | HTML | 2024年 6月 26日 |
| Application brief | Benefits of Hall-Effect Sensors in Contact Sensors (Rev. A) | PDF | HTML | 2024年 9月 18日 | |
| EVM User's guide | TMAG3001 Evaluation Module User's Guide (Rev. A) | PDF | HTML | 2024年 6月 6日 | |
| Application note | Gear-Tooth Detection With Back-Biased 3D Hall-Effect Sensors | PDF | HTML | 2024年 4月 29日 | |
| User guide | Joystick and Lever Design With Hall-Effect Sensors (Rev. A) | PDF | HTML | 2023年 12月 21日 | |
| Application note | Low Power Design Using Hall-Effect Sensors (Rev. A) | PDF | HTML | 2023年 12月 21日 | |
| Application brief | Introduction to TI Magnetic Sense Simulator Features | PDF | HTML | 2023年 12月 5日 | |
| User guide | Texas Instruments' Magnetic Sense Simulator User's Guide | PDF | HTML | 2023年 12月 4日 | |
| Certificate | TMAG3001EVM EU Declaration of Conformity (DoC) | 2023年 9月 20日 |
設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
開發板
TMAG3001EVM — 適用於具有 I²C Ω 和可編程開關之三軸線性霍爾效應感測器的 TMAG3001 評估模組
TMAG3001 評估模組 (EVM) 是易於使用的平台，用於評估 TMAG3001 的主要功能和性能，該裝置是線性 3D 霍爾效應感測器。TMAG3001EVM 包含一個磁鐵和 TMAG3001 子板。此 EVM 可搭配感測器控制器電路板 (TI-SCB) (另售) 使用，如此可啟用隨附的 GUI。此外也隨附 3D 列印旋轉及推送模組，以單一裝置測試角度量測與按鈕的一般功能。
開發模組 (EVM) 的 GUI
TMAG3001EVM-GUI — GUI for TMAG3001 evaluation module (EVM)
TMAG3001EVM GUI will allow users to measure and plot the magnetic fields sensed by the device
支援產品和硬體
產品
多軸線性與角度位置感測器
硬體開發
開發板
支援軟體
TMAG3001EVM-BSL — TMAG3001EVM BSL batch file
Provides an executable that can be used by customers to flash their TI-SCB with the firmware needed to interface with the TMAG3001EVM GUI
支援產品和硬體
產品
多軸線性與角度位置感測器
硬體開發
開發板
計算工具
SBAR012 — Angle Error Calculator for Linear 3D Hall-effect Sensors
Angle Error Calculator for Linear 3D Hall-effect Sensors
支援產品和硬體
產品
多軸線性與角度位置感測器
模擬工具
TI-MAGNETIC-SENSE-SIMULATOR — TI Magnetic sensing simulation tool
The TI-MAGNETIC-SENSE-SIMULATOR (TIMSS) webtool estimates magnetic flux density and TI magnetic sensor outputs for magnetic position sensing systems. Select from our portfolio of magnetic sensors to thoroughly emulate electro-mechanical performance of your design. The tool supports various magnet (...)
支援產品和硬體
產品
霍爾效應鎖存器和開關
線性霍爾效應感測器
多軸線性與角度位置感測器
硬體開發
開發板
軟體
計算工具
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| DSBGA (YBG) | 6 | Ultra Librarian |
訂購與品質
內含資訊：
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 認證摘要
- 進行中持續性的可靠性監測
內含資訊：
- 晶圓廠位置
- 組裝地點
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。