TPS22946
- Ultralow Quiescent Current 1 µA (Typical)
at VIN = 1.8 V - Input Voltage Range: 1.62 V to 5.5 V
- Low ON-Resistance
- rON = 300 mΩ at VIN = 5.5 V
- rON = 400 mΩ at VIN = 3.3 V
- rON = 500 mΩ at VIN = 2.5 V
- rON = 600 mΩ at VIN = 1.8 V
- Selectable Minimum Current Limit:
155 mA, 70 mA, or 30 mA - Integrated Inrush Current Time-out (8 ms)
- Shutdown Current: < 1 µA
- Thermal Shutdown
- Fault Blanking
- Auto Restart
- Overcurrent Condition Time-out (Automatic
Disable for Permanent Overcurrent) - 1.8-V Compatible Control Input
- ESD Performance Tested Per JESD 22
- 6000-V Human-Body Model
(A114-B, Class II)
- 6000-V Human-Body Model
- Tiny DSGBA Package 1.4 mm × 0.9 mm (YZP)
The TPS22946 is an ultralow power load switch that provides protection to systems and loads in high-current conditions. The device contains a 300-mΩ current-limited P-channel MOSFET that can operate over an input voltage range of 1.62 V to 5.5 V. The switch is controlled by an on/off input (ON), which can interface directly with low-voltage control signals. The TPS22946 includes thermal shutdown protection that prevents damage to the device when a continuous over-current condition causes excessive heating by turning off the switch.
When the switch current reaches the maximum limit, the TPS22946 operates in a constant-current mode to prohibit excessive currents from causing damage. The current limit can be selected using the CL input: a high CL input sets the current limit to 155 mA, a low CL input sets the current limit to 70 mA, and a floating CL input sets the current limit to 30 mA.
If the constant current condition persists after 10 ms, the switch is turned off and the fault signal pin (OC) is pulled low. The TPS22946 has an auto-restart feature which turns the switch on again after 70 ms if the ON pin is still active. If the TPS22946 remains in an over-current condition for 5 seconds, the device shuts off until it is turned on again by setting the ON control signal off and then on.
If the device is used to protect an LDO, the inrush current required by the LDO at startup can, in some cases, exceed the current limit and initiate a blanking (current limiting) condition. The TPS22946 provides allowance for this scenario during startup of the LDO by temporarily increasing the current limit to 435 mA for 8 ms after the load switch is enabled.
The TPS22946 is available in space-saving 6-pin DSBGA (YZP) package. The device is characterized for operation over the free-air temperature range of 40°C to 85°C.
기술 자료
유형 | 직함 | 날짜 | ||
---|---|---|---|---|
* | Data sheet | TPS22946 Ultralow Power, Low Input Voltage, Current-Limited Load Switch With Shutoff, Auto-Restart, and Overcurrent Condition Time-Out datasheet (Rev. B) | PDF | HTML | 2015/04/08 |
Application note | Load Switch Thermal Considerations (Rev. A) | 2018/10/11 | ||
Application note | Basics of Load Switches (Rev. A) | 2018/09/05 | ||
Selection guide | Power Management Guide 2018 (Rev. R) | 2018/06/25 | ||
Application note | Basics of eFuses (Rev. A) | 2018/04/05 | ||
Technical article | How to use load switches to power your wearable | PDF | HTML | 2015/10/19 | |
EVM User's guide | Using the TPS22946EVM-499 Single Channel Load Switch IC | 2013/02/26 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
TPS22946EVM-499 — TPS22946 전류 제한 부하 스위치 평가 모듈
The TPS22946EVM-499 evaluation module (EVM) allows the user to connect power to and control the TPS22946 ultra-small, CSP-6 package load switch. Parameters such as on state resistance, slew rate and current limit properties can be easily evaluated.
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
TIDA-010019 — 온도 센서에 냉접점 보상을 제공하기 위한 RTD 교체 레퍼런스 설계
TIDA-010008 — 그리드 애플리케이션의 과도 차단 기능을 위한 평면 클램프 TV 기반 레퍼런스 설계
패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
---|---|---|
DSBGA (YZP) | 6 | Ultra Librarian |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.