TPS25984
- Input operating voltage range: 4.5 V to 16 V
- Absolute maximum: 20 V
- Withstands negative voltages up to –1 V at output
- Integrated FET with ultra-low on-resistance: 0.8 mΩ (typical)
- Rated for RMS current of 55 A and peak current of 70 A
- Supports parallel connection of multiple eFuses for higher current support
- Active device state synchronization and load sharing during start-up and steady-state
- Robust overcurrent protection
- Adjustable overcurrent threshold (I OCP): 10 A to 55 A with accuracy of ±5%
- Circuit-breaker response during steady state operation with adjustable transient overcurrent timer (ITIMER) to support peak currents up to 2 × I OCP
- Adjustable active current limit during start-up (I LIM)
- Robust short-circuit protection
- Fast-trip response (< 200 ns) to output short-circuit events
- Adjustable threshold (2 × I OCP)
- Immune to supply line transients — no nuisance tripping
- Precise analog load current monitoring
- Accuracy: ±1.4 %
- Bandwidth: > 500 kHz
- Fast overvoltage protection (fixed 16.7-V threshold)
- Adjustable output slew rate control (dVdt) for inrush current protection
- Active high enable input with adjustable undervoltage lockout (UVLO)
- Overtemperature Protection (OTP) to ensure FET SOA
- Guaranteed FET SOA: 10 W√s
- Integrated FET health monitoring and reporting
- Analog die temperature monitor output (TEMP)
- Dedicated fault indication pin ( FLT)
- Power-Good indication pin (PG)
- Small footprint: QFN 5 mm × 5 mm
- 100% Pb free
The TPS25984x is an integrated, high-current circuit protection and power management solution in a small package. The device provides multiple protection modes using very few external components and is a robust defense against overloads, short circuits, and excessive inrush current.
Applications with particular inrush current requirements can set the output slew rate with a single external capacitor. Output current limit level can be set by user as per system needs. A user adjustable overcurrent blanking timer allows systems to support transient peaks in the load current without tripping the eFuse.
Multiple TPS25984x devices can be connected in parallel to increase the total current capacity for high power systems. All devices actively synchronize their operating state and share current during start-up as well as steady state to avoid over-stressing some of the devices which can result in premature or partial shutdown of the parallel chain.
An integrated fast and accurate sense analog load current monitor facilitates predictive maintenance and advanced dynamic platform power management techniques such as Intel PSYS and PROCHOT™ to maximize system throughput and power supply utilization.
The devices are characterized for operation over a junction temperature range of –40°C to +125°C.
기술 자료
| 유형 | 직함 | 날짜 | ||
|---|---|---|---|---|
| * | Data sheet | TPS25984x 4.5 V – 16 V, 0.8-mΩ, 70-A Stackable eFuse With Accurate and Fast Current Monitor datasheet (Rev. A) | PDF | HTML | 2023/10/12 |
| Application note | Implementation of PSYS Monitor Using TPS25984, TPS25985, or TPS25990 eFuses | PDF | HTML | 2023/11/15 | |
| EVM User's guide | TPS25984 Evaluation Module (EVM) (Rev. A) | PDF | HTML | 2023/11/02 | |
| Certificate | TPS25984EVM EU RoHS Declaration of Conformity (DoC) | 2022/11/11 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
TPS25984EVM — TPS25984 4.5V~16V, 70A, 0.8mΩ eFuse용 평가 모듈
TPS25984 eFuse 평가 보드는 텍사스 인스트루먼트(TI)의 TPS25984 eFuse에 대한 레퍼런스 회로 평가를 지원합니다. TPS25984 장치는 0.8mΩ FET가 결합된 4.5V~16V, 70A eFuse입니다. 과전류, 돌입 전류 관리, 조정식 과전류 과도 블랭킹 타이머, 프로그래머블 저전압, 과전압 보호 기능을 통한 구성 기능이 포함되어 있습니다.
TVS-RECOMMENDATION-CALC — TVS diode recommendation tool
지원되는 제품 및 하드웨어
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| WQFN-FCRLF (RZJ) | 32 | Ultra Librarian |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.