首頁 電源管理 LED 驅動器 RGB LED 驅動器
首頁
電源管理
LED 驅動器
RGB LED 驅動器

LP5811

現行

具備 I2C 和自動動畫控制的同步升壓 4 通道 RGBW LED 驅動器

立即訂購
產品規格表

LP5811

現行
產品規格表 立即訂購

產品詳細資料

Number of channels 4 LED current per channel (mA) 50 LED configuration Parallel Program memory Yes Topology Boost Programmable ramp control Yes Vin (min) (V) 0.5 Vin (max) (V) 5.5 Iout (max) (A) 0.2 Features Analog/PWM mixed dimming, Constant current, I2C control, LED Open Detection, LED Short Detection, Programmable lighting engines, Thermal shutdown Iq (typ) (mA) 0.4 Shutdown current (ISD) (typ) (µA) 0.1 Operating temperature range (°C) -40 to 85 Rating Catalog
Number of channels 4 LED current per channel (mA) 50 LED configuration Parallel Program memory Yes Topology Boost Programmable ramp control Yes Vin (min) (V) 0.5 Vin (max) (V) 5.5 Iout (max) (A) 0.2 Features Analog/PWM mixed dimming, Constant current, I2C control, LED Open Detection, LED Short Detection, Programmable lighting engines, Thermal shutdown Iq (typ) (mA) 0.4 Shutdown current (ISD) (typ) (µA) 0.1 Operating temperature range (°C) -40 to 85 Rating Catalog
DSBGA (YBH) 12 2.5116 mm² 1.82 x 1.38 WSON (DRR) 12 9 mm² 3 x 3
  • Operating voltage range:
    • Input voltage (VIN) range: 0.5V to 5.5V
    • 1.8V minimum input voltage for start-up
    • Logic pins compatible with 1.8V, 3.3V, and 5V
  • High efficiency synchronous boost converter
    • Output voltage (VOUT) range: 3V to 5.5V
    • 140mΩ (HS) / 60mΩ (LS) MOSFETs
    • 1.6A valley switching current limit
    • 95% efficiency at VIN = 4.2V, VOUT = 5.0V, IOUT = 300mA
    • Pass-through mode when VIN > VOUT setting

    • True disconnection between input and output during shutdown

  • 4 constant current sinks with high precision:
    • 0.1mA to 51mA per current sink
    • Device-to-device error: max ±5%
    • Channel-to-channel error: max ±5%
    • Ultra-low headroom voltage: 110mV (typ.) at 25.5mA; 210mV (typ.) at 51mA
    • PWM phase shift configurable for each LED
  • Ultra-low power consumption:
    • Shutdown: ISD = 0.1µA (typical) when EN = Low
    • Standby: ISTB = 26µA (typical) when EN = High and CHIP_EN = 0 (data retained)
    • Active: INOR = 0.45mA (typical) when LED current = 25.5mA
  • Analog dimming (current gain control)
    • Global 1-bit Maximum Current (MC): 25.5mA or 51mA
    • Individual 8-bit Dot Current (DC) setting
  • PWM dimming up to audible-noise-free 24kHz
    • Individual 8-bit PWM dimming resolution
    • Linear or exponential dimming curves
  • Autonomous animation engine control
  • Individual LED dot open/short detection
  • Integrated de-ghosting function
  • 1MHz (max.) I2C interface
  • –40°C to 85°C operating temperature range
  • Operating voltage range:
    • Input voltage (VIN) range: 0.5V to 5.5V
    • 1.8V minimum input voltage for start-up
    • Logic pins compatible with 1.8V, 3.3V, and 5V
  • High efficiency synchronous boost converter
    • Output voltage (VOUT) range: 3V to 5.5V
    • 140mΩ (HS) / 60mΩ (LS) MOSFETs
    • 1.6A valley switching current limit
    • 95% efficiency at VIN = 4.2V, VOUT = 5.0V, IOUT = 300mA
    • Pass-through mode when VIN > VOUT setting

    • True disconnection between input and output during shutdown

  • 4 constant current sinks with high precision:
    • 0.1mA to 51mA per current sink
    • Device-to-device error: max ±5%
    • Channel-to-channel error: max ±5%
    • Ultra-low headroom voltage: 110mV (typ.) at 25.5mA; 210mV (typ.) at 51mA
    • PWM phase shift configurable for each LED
  • Ultra-low power consumption:
    • Shutdown: ISD = 0.1µA (typical) when EN = Low
    • Standby: ISTB = 26µA (typical) when EN = High and CHIP_EN = 0 (data retained)
    • Active: INOR = 0.45mA (typical) when LED current = 25.5mA
  • Analog dimming (current gain control)
    • Global 1-bit Maximum Current (MC): 25.5mA or 51mA
    • Individual 8-bit Dot Current (DC) setting
  • PWM dimming up to audible-noise-free 24kHz
    • Individual 8-bit PWM dimming resolution
    • Linear or exponential dimming curves
  • Autonomous animation engine control
  • Individual LED dot open/short detection
  • Integrated de-ghosting function
  • 1MHz (max.) I2C interface
  • –40°C to 85°C operating temperature range

The LP5811 is a synchronous boost 4-channel RGBW LED driver with autonomous animation engine control. The device is ideal to support battery-powered applications with 0.5V to 5.5V input voltage range, and it has ultra-low normal operation current with 0.4mA (typical) when illuminate LEDs.

The integrated synchronous boost converter maintains excellent efficiency and keeps the brightness of LEDs stable over a wide operating voltage range. Output voltage can be selected for different LED forward voltage from 3V to 5.5V with 0.1V step. The boost converter can power not only the LEDs driven by the device itself, but also other loads in the system. If the boost converter need to be bypassed, VOUT is used as the power supply input for the LED driver blocks.

Both analog dimming and PWM dimming methods are adopted to achieve powerful dimming performance. The output current of each LED can be adjusted with 256 steps from 0.1mA to 25.5mA or 0.2mA to 51mA. The 8-bit PWM generator enables smooth and audible-noise-free dimming control for LED brightness.

The autonomous animation engine can significantly reduce the real-time loading of controller. Each LED can be configured through the related registers to realize vivid and fancy lighting effects. The device can generate 6MHz clock signal and use it for synchronizing the lighting effects among multiple devices.

The LP5811 is a synchronous boost 4-channel RGBW LED driver with autonomous animation engine control. The device is ideal to support battery-powered applications with 0.5V to 5.5V input voltage range, and it has ultra-low normal operation current with 0.4mA (typical) when illuminate LEDs.

The integrated synchronous boost converter maintains excellent efficiency and keeps the brightness of LEDs stable over a wide operating voltage range. Output voltage can be selected for different LED forward voltage from 3V to 5.5V with 0.1V step. The boost converter can power not only the LEDs driven by the device itself, but also other loads in the system. If the boost converter need to be bypassed, VOUT is used as the power supply input for the LED driver blocks.

Both analog dimming and PWM dimming methods are adopted to achieve powerful dimming performance. The output current of each LED can be adjusted with 256 steps from 0.1mA to 25.5mA or 0.2mA to 51mA. The 8-bit PWM generator enables smooth and audible-noise-free dimming control for LED brightness.

The autonomous animation engine can significantly reduce the real-time loading of controller. Each LED can be configured through the related registers to realize vivid and fancy lighting effects. The device can generate 6MHz clock signal and use it for synchronizing the lighting effects among multiple devices.

filter 尋找其它 RGB LED 驅動器
下載 觀看有字幕稿的影片 影片

您可能會感興趣的類似產品

open-in-new 比較替代產品
引腳對引腳且具備與所比較裝置相同的功能
LP5813 現行 具備 I2C 和自動動畫控制的 4 x 3 矩陣 RGB LED 驅動器 4x3 TCM matrix and sync boost
功能與所比較的裝置相似
LP5810 現行 具備 I2C 和自動動畫控制的 4 通道 RGBW LED 驅動器 4 channel and linear
LP5812 現行 具備 I2C 和自動動畫控制的 4 x 3 矩陣 RGB LED 驅動器 4x3 TCM matrix and linear

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 2
類型 標題 日期
* Data sheet LP5811 Synchronous Boost 4-Channel RGBW LED Driver with Autonomous Control datasheet (Rev. B) PDF | HTML 2024年 12月 2日
User guide LP5811 Synchronous Boost 4-Channel RGBW LED Driver Register Map PDF | HTML 2024年 9月 24日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

LP5811-10EVM — LP5811 和 LP5810 評估模組

LP5811 和 LP5810 評估模組 (EVM) 展示了 LP5811 和 LP5810 LED 驅動器的所有功能。LP581XEVM-GUI 用於透過 USB2ANY 介接至 EVM。EVM 具有透過 USB2ANY 介面轉接器的 I²C 輸入。

使用指南: PDF | HTML
TI.com 無法提供
開發板

LP5813-12WCSPEVM — 具自動控制功能且適用於 4 x 3 LED 矩陣驅動器的 LP5813/LP5812 評估模組

LP5813/12 評估模組展示 LP5813 和 LP5812 4 × 3 矩陣 RGB LED 驅動器的所有功能。兩個裝置之間的差別在於具有或未具有同步升壓功能。LP581x 圖形使用者介面 (GUI) 用於透過 USB2ANY 介接至 EVM。EVM 具有透過 USB2ANY 介面轉接器的 I2C 輸入。

使用指南: PDF | HTML
TI.com 無法提供
開發板

LP5813-12WSONEVM — 適用於 WSON 封裝的 LP5813 和 LP5812 評估模組

LP5813 和 LP5812 評估模組 (EVM) 展示了具有自主控制功能的 LP5813 和 LP5812 4 × 3 矩陣 RGB LED 驅動器的所有功能。‌兩種產品之間的差別在於是否具有同步升壓功能。LP5813 和 LP5812 都位於在同一塊電路板上，請透過 USB2ANY 連接器和跳線設定選擇需要評估的產品。提供名為 LP581x GUI 的圖形使用者介面或 GUI，可透過 USB2ANY 介面轉接器將 USB 介接至 EVM。

使用指南: PDF | HTML
TI.com 無法提供
開發模組 (EVM) 的 GUI

LP581XEVM-GUI — GUI for LP581x Family LED Drivers

The LP581x-GUI is a evaluation tool for LP581x family devices, it can be used to evaluate the LP581xEVM or customized board through USB2ANY interface adapter and showcases all the features of the LP581x family devices.
支援產品和硬體

支援產品和硬體

產品
RGB LED 驅動器
LP5813 — 具備 I2C 和自動動畫控制的 4 x 3 矩陣 RGB LED 驅動器 LP5812 — 具備 I2C 和自動動畫控制的 4 x 3 矩陣 RGB LED 驅動器 LP5811 — 具備 I2C 和自動動畫控制的同步升壓 4 通道 RGBW LED 驅動器 LP5810 — 具備 I2C 和自動動畫控制的 4 通道 RGBW LED 驅動器
硬體開發
開發板
LP5813-12WCSPEVM — 具自動控制功能且適用於 4 x 3 LED 矩陣驅動器的 LP5813/LP5812 評估模組 LP5813-12WSONEVM — 適用於 WSON 封裝的 LP5813 和 LP5812 評估模組 LP5811-10EVM — LP5811 和 LP5810 評估模組
啟動 下載選項
模擬工具

PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具

PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
要求
封裝 針腳 CAD 符號、佔位空間與 3D 模型
DSBGA (YBH) 12 Ultra Librarian
WSON (DRR) 12 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片