TPSI3100-Q1
- Drives external power transistors
- No isolated secondary supply required
- 15.8-V gate drive, 1.5/2.5-A peak source and sink current
- 5-kVRMS reinforced isolation
- Up to 25-mW, 5-V supply for external auxiliary circuitry
- Dual isolated high-speed comparators with integrated voltage reference ±1.5%
- Open-drain outputs for fault and alarm indicators
- AEC Q-100 qualified for automotive applications:
- Temperature grade 1: –40°C to +125°C, TA
- Functional Safety-Capable
- Safety-related certifications
- Planned: 7070-VPK reinforced isolation per DIN EN IEC 60747-17 (VDE 0884-17)
- Planned: 5-kVRMS isolation for 1 minute per UL 1577
The TPSI3100-Q1 is a fully integrated isolated switch driver, which when combined with an external power switch, forms a complete isolated solid state relay solution. With a gate drive voltage of 15.8-V with 1.5/2.5-A peak source/sink current, a large availability of power switches can be used to meet many application needs. The TPSI3100-Q1 generates its own secondary bias supply from power received on its primary side, so no isolated secondary supply bias is required. The TPSI3100-Q1 provides additional power via the nominal 5-V rail (VDDM) for use by auxiliary circuits to perform various function such as current and voltage monitoring or remote temperature detection. The TPSI3100-Q1 isolation is extremely robust with much higher reliability, lower power consumption, and increased temperature ranges than those found using traditional mechanical relays and optocouplers.
The TPSI3100-Q1 integrates a communication back-channel that transfers status information from the secondary side to the primary side via open-drain outputs, PGOOD (Power Good), FLT1 (Fault 1), and ALM1 (Alarm 1). Dual high-speed comparators with an integrated shared voltage reference are used to assert FLT1 and ALM1. When the comparator input, FLT1_CMP, exceeds the voltage reference, the driver is immediately asserted low and FLT1 is also driven low, indicating to the system that a fault has occurred. This is useful for disabling the external switch with low latency on critical events, such as over-current detection. When the comparator input, ALM1_CMP, exceeds the voltage reference, ALM1 signal is asserted low, but no action is taken by the driver. This may be useful as an alarm or warning indicator for over-temperature or over-voltage events.
The TPSI310xL-Q1 series offers a latch based fault indicator. When a fault is detected, the driver and the fault indicator are asserted low and remain latched, until EN is asserted low. The TPSI310x-Q1 series has a non-latched fault indicator. If the fault event is no longer present, FLT1 deasserts and the driver, after a specified recovery period, follows the state of the EN pin. If the fault event still remains, both the fault indicator and the driver remain asserted low.
기술 자료
유형 | 직함 | 날짜 | ||
---|---|---|---|---|
* | Data sheet | TPSI3100-Q1 Automotive Reinforced Isolated Switch Driver With 15-V Gate Supply and Dual Isolated Comparators datasheet | PDF | HTML | 2023/12/18 |
Functional safety information | TPSI3100-Q1 Functional Safety FIT Rate, FMD, and Pin FMA | PDF | HTML | 2023/12/13 | |
EVM User's guide | TPSI31xx-Q1 Evaluation Module User's Guide | PDF | HTML | 2023/11/28 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
TPSI31XXQ1EVM — TPSI31xx-Q1 평가 모듈
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
---|---|---|
UNKNOWN (DVX) | 16 | Ultra Librarian |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.