Inicio Gestión de la energía Controladores LED Controladores para LED de retroiluminación
Inicio
Gestión de la energía
Controladores LED
Controladores para LED de retroiluminación

TPS60250

ACTIVO

Bomba de carga de alta eficiencia para 7 WLED con interfaz I2C con dirección del esclavo I2C 0x77

Haga su pedido ahora
Hoja de datos

TPS60250

ACTIVO
Hoja de datos Haga su pedido ahora

Detalles del producto

Number of channels 7 Vin (min) (V) 3 Vin (max) (V) 6 Vout (min) (V) 2.7 Vout (max) (V) 6.5 Type Capacitive Switching frequency (max) (kHz) 875 Duty cycle (max) (%) 0.23 LED current per channel (mA) 25 Peak efficiency (%) 93 Topology Boost Features Analog Dimming, Enable/Shutdown, I2C control, Integrated Switch, Load Disconnect During Shutdown, OVP, Soft Start, Synchronous Rectification Operating temperature range (°C) -40 to 85 Rating Catalog
Number of channels 7 Vin (min) (V) 3 Vin (max) (V) 6 Vout (min) (V) 2.7 Vout (max) (V) 6.5 Type Capacitive Switching frequency (max) (kHz) 875 Duty cycle (max) (%) 0.23 LED current per channel (mA) 25 Peak efficiency (%) 93 Topology Boost Features Analog Dimming, Enable/Shutdown, I2C control, Integrated Switch, Load Disconnect During Shutdown, OVP, Soft Start, Synchronous Rectification Operating temperature range (°C) -40 to 85 Rating Catalog
WQFN (RTE) 16 9 mm² 3 x 3
  • 3.0 V to 6.0 V Input Voltage Range
  • ×1 and ×1.5 Charge Pump
  • Fully Programmable Current with I2C
    • 64 Dimming Steps with 25mA Maximum (Sub and Main Display Banks)
    • 4 Dimming Steps with 80mA Maximum (DM5 for Auxiliary Application)
  • 2% Current Matching for Sub LEDs at Light Load Condition (Each 100µA)
  • 750 kHz Charge Pump Frequency
  • Continuous 230mA Maximum Output Current
  • Auto Switching Between ×1 and ×1.5 Mode for Maximum Efficiency
  • Built-in Soft Start and Current Limit
  • Open Lamp Detection
  • 16-Pin 3mm x 3mm QFN
  • TPS60250 (I2C Slave Address: 1110111)
  • TPS60252 (I2C Slave Address: 1110110)
  • APPLICATIONS
    • Cellular Phones
    • PDA, PMP, GPS (Up To 4 Inch LCD Display)
    • Multidisplay Handheld Devices
  • 3.0 V to 6.0 V Input Voltage Range
  • ×1 and ×1.5 Charge Pump
  • Fully Programmable Current with I2C
    • 64 Dimming Steps with 25mA Maximum (Sub and Main Display Banks)
    • 4 Dimming Steps with 80mA Maximum (DM5 for Auxiliary Application)
  • 2% Current Matching for Sub LEDs at Light Load Condition (Each 100µA)
  • 750 kHz Charge Pump Frequency
  • Continuous 230mA Maximum Output Current
  • Auto Switching Between ×1 and ×1.5 Mode for Maximum Efficiency
  • Built-in Soft Start and Current Limit
  • Open Lamp Detection
  • 16-Pin 3mm x 3mm QFN
  • TPS60250 (I2C Slave Address: 1110111)
  • TPS60252 (I2C Slave Address: 1110110)
  • APPLICATIONS
    • Cellular Phones
    • PDA, PMP, GPS (Up To 4 Inch LCD Display)
    • Multidisplay Handheld Devices

The TPS60250/2 are high efficiency, constant frequency charge pump DC/DC converters that use dual mode 1× and 1.5× conversions to maximize efficiency over the input voltage range. The devices drive up to five white LEDs for the main display and up to two white LEDs for the sub display with regulated constant current for uniform intensity. By utilizing adaptive 1×/1.5× charge pump modes and very low-dropout current regulators, the TPS60250/2 achieve high efficiency over the full 1-cell lithium-battery input voltage range.

Four enable inputs, ENmain, ENsub1, ENsub2, and ENaux, available through the I2C, are used for simple on/off controls for the independent main, sub1, sub2, and DM5 displays, respectively. To lower the operating current when using one sub display LED, the devices provide completely separate operation for the sub display LEDs.

The TPS60250/2 are available in a 16-pin 3mm x 3mm thin QFN.

The TPS60250/2 are high efficiency, constant frequency charge pump DC/DC converters that use dual mode 1× and 1.5× conversions to maximize efficiency over the input voltage range. The devices drive up to five white LEDs for the main display and up to two white LEDs for the sub display with regulated constant current for uniform intensity. By utilizing adaptive 1×/1.5× charge pump modes and very low-dropout current regulators, the TPS60250/2 achieve high efficiency over the full 1-cell lithium-battery input voltage range.

Four enable inputs, ENmain, ENsub1, ENsub2, and ENaux, available through the I2C, are used for simple on/off controls for the independent main, sub1, sub2, and DM5 displays, respectively. To lower the operating current when using one sub display LED, the devices provide completely separate operation for the sub display LEDs.

The TPS60250/2 are available in a 16-pin 3mm x 3mm thin QFN.
filter Buscar otro/a Controladores para LED de retroiluminación
Descargar Ver vídeo con transcripción Video

Documentación técnica

star =Principal documentación para este producto seleccionada por TI
No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.
Ver todo 6
Tipo Título Fecha
* Data sheet High Efficiency Charge Pump for 7 WLEDs with I2C Interface datasheet (Rev. C) 23 abr 2008
White paper Common LED Functions and LED Driver Design Considerations 21 sep 2020
Application note Performing Accurate PFM Mode Efficiency Measurements (Rev. A) 11 dic 2018
Selection guide Power Management Guide 2018 (Rev. R) 25 jun 2018
Application note Extending the Soft Start Time Without a Soft Start Pin (Rev. B) 15 jun 2017
EVM User's guide TPS60250EVM-185 (Rev. B) 12 dic 2012

Diseño y desarrollo

Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.

Placa de evaluación

TPS60250EVM-185 — Módulo de evaluación TPS60250

The TPS60250EVM-185 is an evaluation module for the TPS60250 high efficiency charge pump DC/DC converter for WLED drivers. The TPS60250 uses a dual mode load switch 1X and 1.5X conversion to maximize efficiency. It drives up to five white LEDs in the main display and up to two white LEDs with (...)

Guía del usuario: PDF
No disponible en TI.com
GUI para el módulo de evaluación (EVM)

SLVC113 — TPS6025xEVM Software

Productos y hardware compatibles

Productos y hardware compatibles

Productos
Controladores para LED de retroiluminación
TPS60250 — Bomba de carga de alta eficiencia para 7 WLED con interfaz I2C con dirección del esclavo I2C 0x77 TPS60252 — Bomba de carga de alta eficiencia para 7 WLED con interfaz I2C con dirección del esclavo I2C 0x76
Desarrollo de hardware
Placa de evaluación
TPS60250EVM-185 — Módulo de evaluación TPS60250
Descargar
Archivo Gerber

TPS60250EVM-185 Gerber Files

SLVC119.ZIP (106 KB)
Descargar
Herramienta de simulación

PSPICE-FOR-TI — PSpice® para herramienta de diseño y simulación de TI

PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
Solicitar
Encapsulado Pines Símbolos CAD, huellas y modelos 3D
WQFN (RTE) 16 Ultra Librarian
Se aplican los Términos y condiciones estándar de TI para los elementos de evaluación.

Pedidos y calidad

Información incluida:
  • RoHS
  • REACH
  • Marcado del dispositivo
  • Acabado de plomo/material de la bola
  • Clasificación de nivel de sensibilidad a la humedad (MSL) / reflujo máximo
  • Estimaciones de tiempo medio entre fallas (MTBF)/fallas en el tiempo (FIT)
  • Contenido del material
  • Resumen de calificaciones
  • Monitoreo continuo de confiabilidad
Información incluida:
  • Lugar de fabricación
  • Lugar de ensamblaje

Soporte y capacitación

Foros de TI E2E™ con asistencia técnica de los ingenieros de TI

Ver todos los temas del foro en inglés

El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.

Si tiene preguntas sobre la calidad, el paquete o el pedido de productos de TI, consulte el soporte de TI. ​​​​​​​​​​​​​​

Videos