首頁 電源管理 電源開關 eFuses 和熱插拔制器
首頁
電源管理
電源開關
eFuses 和熱插拔制器

TPS2521

現行

具有整合式反向極性保護的 2.7-V 至 5.7-V、31-mΩ、4-A eFuse

立即訂購
產品規格表

TPS2521

現行
產品規格表 立即訂購

產品詳細資料

FET Internal Ron (typ) (mΩ) 31 Vin (min) (V) 2.7 Vin (max) (V) 5.7 Vabsmax_cont (V) 28 Current limit (min) (A) 0.5 Current limit (max) (A) 4.44 Overcurrent response current limiting Fault response Auto-retry, Latch-off Soft start Adjustable Overvoltage response Clamp Features Analog current monitor, Fault output, Input reverse polarity protection, Overvoltage clamping, Power good signal, Reverse current blocking always, Thermal shutdown UL recognition IEC62368, UL2367 Rating Catalog Device type eFuses and hot swap controllers Operating temperature range (°C) -40 to 125 Function Adjustable current limit, Current monitoring, Inrush current control, Overvoltage protection, Power good signal, Reverse current blocking, Reverse polarity protection, Short circuit protection, Thermal shutdown Quiescent current (Iq) (typ) (A) 0.000411 Quiescent current (Iq) (max) (A) 0.000593
FET Internal Ron (typ) (mΩ) 31 Vin (min) (V) 2.7 Vin (max) (V) 5.7 Vabsmax_cont (V) 28 Current limit (min) (A) 0.5 Current limit (max) (A) 4.44 Overcurrent response current limiting Fault response Auto-retry, Latch-off Soft start Adjustable Overvoltage response Clamp Features Analog current monitor, Fault output, Input reverse polarity protection, Overvoltage clamping, Power good signal, Reverse current blocking always, Thermal shutdown UL recognition IEC62368, UL2367 Rating Catalog Device type eFuses and hot swap controllers Operating temperature range (°C) -40 to 125 Function Adjustable current limit, Current monitoring, Inrush current control, Overvoltage protection, Power good signal, Reverse current blocking, Reverse polarity protection, Short circuit protection, Thermal shutdown Quiescent current (Iq) (typ) (A) 0.000411 Quiescent current (Iq) (max) (A) 0.000593
VQFN-HR (RPW) 10 4 mm² 2 x 2
  • Wide operating input voltage range: 2.7 V to 5.7 V
  • 28-V absolute maximum
  • Withstands negative voltages up to –15 V
  • Integrated back-to-back FETs with low on-resistance: RON = 31 mΩ (typ.)
  • Ideal diode operation with true reverse current blocking
  • Fast overvoltage clamp (OVC) with pin-selectable threshold (3.8 V, 5.7 V) with 5-µs (typ.) response time
  • Overcurrent protection with load current monitor output (ILM)
    • Active current limit response
    • Adjustable threshold (ILIM) 0.5 A–4.44 A
      • ±10% accuracy for ILIM > 1 A
    • Adjustable transient blanking timer (ITIMER) to allow peak currents up to 2 × ILIM
    • Output load current monitor accuracy: ±6% (IOUT ≥ 1 A)
  • Fast-trip response for short-circuit protection
    • 500-ns (typ.) response time
    • Adjustable (2 × ILIM) and fixed thresholds
  • Active High Enable input with adjustable undervoltage lockout threshold (UVLO)
  • Adjustable output slew rate control (dVdt)
  • Overtemperature protection
  • Power Good indication (PG) with adjustable threshold (PGTH)
  • UL 2367 recognition
    • File No. E169910
    • RILM ≥ 750 Ω
  • IEC 62368-1 CB certified
  • Small footprint: QFN 2 mm × 2 mm, 0.45-mm pitch
  • Wide operating input voltage range: 2.7 V to 5.7 V
  • 28-V absolute maximum
  • Withstands negative voltages up to –15 V
  • Integrated back-to-back FETs with low on-resistance: RON = 31 mΩ (typ.)
  • Ideal diode operation with true reverse current blocking
  • Fast overvoltage clamp (OVC) with pin-selectable threshold (3.8 V, 5.7 V) with 5-µs (typ.) response time
  • Overcurrent protection with load current monitor output (ILM)
    • Active current limit response
    • Adjustable threshold (ILIM) 0.5 A–4.44 A
      • ±10% accuracy for ILIM > 1 A
    • Adjustable transient blanking timer (ITIMER) to allow peak currents up to 2 × ILIM
    • Output load current monitor accuracy: ±6% (IOUT ≥ 1 A)
  • Fast-trip response for short-circuit protection
    • 500-ns (typ.) response time
    • Adjustable (2 × ILIM) and fixed thresholds
  • Active High Enable input with adjustable undervoltage lockout threshold (UVLO)
  • Adjustable output slew rate control (dVdt)
  • Overtemperature protection
  • Power Good indication (PG) with adjustable threshold (PGTH)
  • UL 2367 recognition
    • File No. E169910
    • RILM ≥ 750 Ω
  • IEC 62368-1 CB certified
  • Small footprint: QFN 2 mm × 2 mm, 0.45-mm pitch

The TPS2521x family of eFuses is a highly integrated circuit protection and power management solution in a small package. The devices provide multiple protection modes using very few external components and are a robust defense against overloads, short-circuits, voltage surges, reverse polarity and excessive inrush current. With integrated back-to-back FETs, reverse current flow from output to input is blocked at all times, making the device well suited for systems which need load side energy hold up storage in case input power supply fails.

Output current limit level can be set with a single external resistor. It is also possible to get an accurate sense of the output load current by measuring the voltage drop across the current limit resistor.

Applications with particular inrush current requirements can set the output slew rate with a single external capacitor. Loads are protected from input overvoltage conditions by clamping the output to a safe fixed maximum voltage (pin selectable).

The devices are available in a 2-mm × 2-mm, 10-pin HotRod QFN package for improved thermal performance and reduced system footprint.

The devices are characterized for operation over a junction temperature range of –40°C to +125°C.

The TPS2521x family of eFuses is a highly integrated circuit protection and power management solution in a small package. The devices provide multiple protection modes using very few external components and are a robust defense against overloads, short-circuits, voltage surges, reverse polarity and excessive inrush current. With integrated back-to-back FETs, reverse current flow from output to input is blocked at all times, making the device well suited for systems which need load side energy hold up storage in case input power supply fails.

Output current limit level can be set with a single external resistor. It is also possible to get an accurate sense of the output load current by measuring the voltage drop across the current limit resistor.

Applications with particular inrush current requirements can set the output slew rate with a single external capacitor. Loads are protected from input overvoltage conditions by clamping the output to a safe fixed maximum voltage (pin selectable).

The devices are available in a 2-mm × 2-mm, 10-pin HotRod QFN package for improved thermal performance and reduced system footprint.

The devices are characterized for operation over a junction temperature range of –40°C to +125°C.

filter 尋找其它 eFuses 和熱插拔制器
下載 觀看有字幕稿的影片 影片

您可能會感興趣的類似產品

open-in-new 比較替代產品
功能與所比較的裝置相似
TPS25947 現行 具有整合式反向極性保護的 2.7V 至 23V、28mΩ、5.5A eFuse Footprint compatible at wider voltage and current range.

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 4
類型 標題 日期
* Data sheet TPS2521xx, 2.7-V–5.7-V, 4-A, 31-mΩ True Reverse Current Blocking eFuse with Input Reverse Polarity Protection datasheet (Rev. A) PDF | HTML 2022年 3月 29日
Certificate TPS25210x CB Test Certificate IEC 62368-1 2022年 1月 19日
Certificate TPS25210x UL2367 Certificate of Compliance E169910 2022年 1月 19日
EVM User's guide TPS25210EVM: Evaluation Module for TPS25210 eFuse PDF | HTML 2021年 3月 31日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TPS25210EVM — 適用於 eFuse 的 TPS25210 評估模組

TPS25210EVM eFuse 評估板可對德州儀器 TPS25210 eFuse 進行參考電路評估。TPS25210 裝置是一款 2.7-V 至 5.7-V、4-A eFuse，具有整合 31-mΩ FET 和反向電流保護、輸入反極性保護、過電流、突波電流保護、可調式過電流瞬態消隱定時器、可編程欠電壓與過電壓保護。

使用指南: PDF | HTML
TI.com 無法提供
模擬型號

TPS25210x PSpice Transient Model

SLVMDK0.ZIP (117 KB) - PSpice Model
下載
計算工具

SLVRBH7 — TPS25210 Design Calculator

支援產品和硬體

支援產品和硬體

產品
eFuses 和熱插拔制器
TPS2521 — 具有整合式反向極性保護的 2.7-V 至 5.7-V、31-mΩ、4-A eFuse
下載
計算工具

TVS-RECOMMENDATION-CALC — TVS diode recommendation tool

This tool suggests suitable TVS for given system parameters and abs max voltage rating of the device.
支援產品和硬體

支援產品和硬體

此設計資源支援此類別中多數產品。

檢查產品詳細資料頁面以確認支援。
下載
模擬工具

PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具

PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
要求
封裝 針腳 CAD 符號、佔位空間與 3D 模型
VQFN-HR (RPW) 10 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片