Herramienta de cálculo
TPS92692-Q1
Controlador LED de alta precisión con modulación de frecuencia de espectro extendido y generador PWM
Hoja de datos
TPS92692-Q1
- Wide Input Voltage: 4.5 V to 65 V
- Better than ± 4% LED Current Accuracy over –40°C to 150°C Junction Temperature Range
- Spread Spectrum Frequency Modulation for Improved EMI
- Comprehensive Fault Protection Circuitry with Current Monitor output and Open Drain Fault Flag Indicator
- Internal Analog Voltage to PWM Duty Cycle Generator for stand-alone Dimming Operation
- Compatible with Direct PWM Input with over 1000:1 Dimming Range
- Analog LED Current Adjust Input (IADJ) with over 15:1 Contrast Ratio
- Integrated P-Channel Driver to enable Series FET Dimming and LED Protection
- TPS92692-Q1: Automotive Q100 Grade 1 Qualified
The TPS92692 and TPS92692-Q1 are high accuracy peak current mode based controllers designed to support step-up/down LED driver topologies. The device incorporates a rail-to-rail current amplifier to measure LED current and spread spectrum frequency modulation technique for improved EMI performance.
This high performance LED controller can independently modulate LED current using either analog or PWM dimming techniques. Linear analog dimming response with over 15:1 range is obtained by varying the voltage across the high impedance analog adjust (IADJ) input. PWM dimming of LED current is achieved by directly modulating the DIM/PWM input pin with the desired duty cycle or by enabling the internal PWM generator circuit. The PWM generator translates the DC voltage at DIM/PWM pin to corresponding duty cycle by comparing it to the internal triangle wave generator. The optional PDRV gate driver output can be used to drive an external P-Channel series MOSFET.
The TPS92692 and TPS92692-Q1 devices support continuous LED status check through the current monitor (IMON) output. The devices also include an open drain fault indicator output to indicate LED overcurrent, output overvoltage and output undervoltage conditions.
Productos similares que pueden interesarle
Funcionalidad similar a la del dispositivo comparado
Documentación técnica
No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.
Ver todo 8 | Tipo | Título | Fecha | ||
|---|---|---|---|---|
| * | Data sheet | TPS92692, TPS92692-Q1 High Accuracy LED Controller With Spread Spectrum Frequency Modulation datasheet | PDF | HTML | 08 mar 2017 |
| Application note | Automotive Front Headlight Selection Guide | PDF | HTML | 16 abr 2021 | |
| Application note | Analog Thermal Foldback With LED Drivers | 10 jun 2020 | ||
| Technical article | Designing daytime running lights, part 2: responding to an LED fault | PDF | HTML | 06 dic 2018 | |
| Technical article | Designing daytime running lights, part 1: adding one-fail-all-fail LED fault detec | PDF | HTML | 04 dic 2018 | |
| White paper | LED Drivers for Automotive Exterior Applications (Rev. B) | 27 mar 2018 | ||
| Selection guide | 汽车外部照明应用的LED驱动器 | 15 mar 2018 | ||
| EVM User's guide | TPS92692 Boost and Boost-to-Battery LED Driver Evaluation Board | 10 mar 2017 |
Diseño y desarrollo
Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.
Placa de evaluación
TPS92692EVM-880 — Módulo de evaluación de controlador LED de impulso y aumento de potencia a batería TPS92692-Q1
The TPS92692EVM-880 is a fully assembled and tested LED driver that can be configured as either a Boost or a Boost-to-Battery topology to power a single string of series connected LEDs. Acurate closed-loop LED current regulation is achieved using a low-offset rail-to-rail current sense amplifier (...)
Guía del usuario: PDF
Modelo de simulación
TPS92692-Q1 Boost and Buck Boost PSpice Transient Model (Rev. A)
SLVMC05A.ZIP (121 KB) - PSpice Model
Herramienta de cálculo
SLVC687 — TPS92692-Q1 Boost Design Calculator
Productos y hardware compatibles
Productos
Controladores LED de iluminación
Controladores para LED en automóviles
Herramienta de simulación
PSPICE-FOR-TI — PSpice® para herramienta de diseño y simulación de TI
PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
Diseños de referencia
TIDA-01581 — Diseño de referencia de controlador LED de cadena doble para luz de conducción diurna automotriz con
This reference design is a dual string LED driver that implements an operational amplifier based circuit which balances the current in two LED rings. The operational amplifier circuit senses current in a reference string and uses feedback from a mirrored string to bias a MOSFET that regulates the (...)
Diseños de referencia
TIDA-050002 — Diseño de referencia de controlador LED de impulso reductor doble de 55 W para faros de foco alto y
This reference design describes a TPS92692-Q1 LED driver in a dual, high-beam and low-beam application with a single controller and power stage. The design operates in boost mode to provide the high beam and in boost to battery mode to provide the low beam. The single controller power stage design (...)
| Encapsulado | Pines | Símbolos CAD, huellas y modelos 3D |
|---|---|---|
| HTSSOP (PWP) | 20 | Ultra Librarian |
Pedidos y calidad
Información incluida:
- RoHS
- REACH
- Marcado del dispositivo
- Acabado de plomo/material de la bola
- Clasificación de nivel de sensibilidad a la humedad (MSL) / reflujo máximo
- Estimaciones de tiempo medio entre fallas (MTBF)/fallas en el tiempo (FIT)
- Contenido del material
- Resumen de calificaciones
- Monitoreo continuo de confiabilidad
Información incluida:
- Lugar de fabricación
- Lugar de ensamblaje
Los productos recomendados pueden tener parámetros, módulos de evaluación o diseños de referencia relacionados con este producto de TI.
Soporte y capacitación
Foros de TI E2E™ con asistencia técnica de los ingenieros de TI
El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.
Si tiene preguntas sobre la calidad, el paquete o el pedido de productos de TI, consulte el soporte de TI.