首頁 電源管理 電源開關 eFuses 和熱插拔制器
首頁
電源管理
電源開關
eFuses 和熱插拔制器

LM25066

現行

具 PMBus 的 2.9-V 至 17-V 熱插拔控制器

立即訂購
產品規格表

LM25066

現行
產品規格表 立即訂購

產品詳細資料

FET External Vin (min) (V) 2.9 Vin (max) (V) 17 Vabsmax_cont (V) 24 Current limit (min) (A) 0.01 Current limit (max) (A) 500 Overcurrent response Circuit breaker, current limiting Fault response Auto-retry, Latch-off Soft start Adjustable Overvoltage response Cut-off Features Current monitoring, Fault output, PMBus, Power good signal Rating Catalog Device type eFuses and hot swap controllers Operating temperature range (°C) -40 to 125 Function Adjustable current limit, Current monitoring, Inrush current control, Overvoltage protection, Power good signal, Short circuit protection, Thermal shutdown Quiescent current (Iq) (typ) (A) 0.0016 Quiescent current (Iq) (max) (A) 0.0004
FET External Vin (min) (V) 2.9 Vin (max) (V) 17 Vabsmax_cont (V) 24 Current limit (min) (A) 0.01 Current limit (max) (A) 500 Overcurrent response Circuit breaker, current limiting Fault response Auto-retry, Latch-off Soft start Adjustable Overvoltage response Cut-off Features Current monitoring, Fault output, PMBus, Power good signal Rating Catalog Device type eFuses and hot swap controllers Operating temperature range (°C) -40 to 125 Function Adjustable current limit, Current monitoring, Inrush current control, Overvoltage protection, Power good signal, Short circuit protection, Thermal shutdown Quiescent current (Iq) (typ) (A) 0.0016 Quiescent current (Iq) (max) (A) 0.0004
WQFN (NHZ) 24 20 mm² 5 x 4
  • Input Voltage Range: 2.9 V to 17 V
  • I2C/SMBus Interface and PMBus™ Compliant
    Command Structure
  • Programmable 25-mV or 46-mV Current Limit
    Threshold
  • Configurable Circuit Breaker Protection for Hard
    Shorts
  • Configurable Undervoltage and Overvoltage
    Lockouts With Hysteresis
  • Remote Temperature Sensing With
    Programmable Warning and Shutdown
    Thresholds
  • Detection and Notification of Damaged MOSFET
    Condition
  • Real-Time Monitoring of VIN, VOUT, IIN, PIN, VAUX
    With 12-bit Resolution and 1-kHz Sampling Rate
  • Current Measurement Accuracy: ±2.4% Over
    Temperature
  • Power Measurement Accuracy: ±3% Over
    Temperature
  • True Input Power Measurement Using
    Simultaneous Sampling of VIN and IIN Accurately
    Averages Dynamic Power Readings
  • Averaging of VIN, IIN, PIN, and VOUT Over
    Programmable Interval Ranging from 0.001 to
    4 Seconds
  • Programmable WARN and FAULT Thresholds
    With SMBA Notification
  • Blackbox Capture of Telemetry Measurements
    and Device Status Triggered by WARN or FAULT
    Condition
  • Full-Featured Application Design and
    Development GUI
  • 24-Lead WQFN Package
  • Input Voltage Range: 2.9 V to 17 V
  • I2C/SMBus Interface and PMBus™ Compliant
    Command Structure
  • Programmable 25-mV or 46-mV Current Limit
    Threshold
  • Configurable Circuit Breaker Protection for Hard
    Shorts
  • Configurable Undervoltage and Overvoltage
    Lockouts With Hysteresis
  • Remote Temperature Sensing With
    Programmable Warning and Shutdown
    Thresholds
  • Detection and Notification of Damaged MOSFET
    Condition
  • Real-Time Monitoring of VIN, VOUT, IIN, PIN, VAUX
    With 12-bit Resolution and 1-kHz Sampling Rate
  • Current Measurement Accuracy: ±2.4% Over
    Temperature
  • Power Measurement Accuracy: ±3% Over
    Temperature
  • True Input Power Measurement Using
    Simultaneous Sampling of VIN and IIN Accurately
    Averages Dynamic Power Readings
  • Averaging of VIN, IIN, PIN, and VOUT Over
    Programmable Interval Ranging from 0.001 to
    4 Seconds
  • Programmable WARN and FAULT Thresholds
    With SMBA Notification
  • Blackbox Capture of Telemetry Measurements
    and Device Status Triggered by WARN or FAULT
    Condition
  • Full-Featured Application Design and
    Development GUI
  • 24-Lead WQFN Package

The LM25066 combines a high-performance hot-swap controller with a PMBus™ compliant SMBus/I2C interface to accurately measure, protect and control the electrical operating conditions of computing and storage blades connected to a backplane power bus. The LM25066 continuously supplies real-time power, voltage, current, temperature and fault data to the system management host via the SMBus interface.

The LM25066 control block includes a unique hot-swap architecture that provides current and power limiting to protect sensitive circuitry during insertion of boards into a live system backplane, or any other hot power source. A fast acting circuit breaker prevents damage in the event of a short circuit on the output. The input undervoltage and overvoltage levels and hysteresis are configurable, as well as the insertion delay time and fault detection time. A temperature monitoring block on the LM25066 interfaces with a low-cost external diode for monitoring the temperature of the external MOSFET or other thermally sensitive components. The POWER GOOD output provides a fast indicator when the input and/or output voltages are outside their programmed range. LM25066 current measurement accuracy is ±2.4% over temperature.

The LM25066 monitoring block computes both the real-time and average values of subsystem operating parameters (VIN, IIN, PIN, VOUT) as well as the peak power. Accurate power averaging is accomplished by averaging the product of the input voltage and current. A black box (Telemetry/Fault Snapshot) function captures and stores telemetry data and device status in the event of a warning or a fault.

The LM25066 combines a high-performance hot-swap controller with a PMBus™ compliant SMBus/I2C interface to accurately measure, protect and control the electrical operating conditions of computing and storage blades connected to a backplane power bus. The LM25066 continuously supplies real-time power, voltage, current, temperature and fault data to the system management host via the SMBus interface.

The LM25066 control block includes a unique hot-swap architecture that provides current and power limiting to protect sensitive circuitry during insertion of boards into a live system backplane, or any other hot power source. A fast acting circuit breaker prevents damage in the event of a short circuit on the output. The input undervoltage and overvoltage levels and hysteresis are configurable, as well as the insertion delay time and fault detection time. A temperature monitoring block on the LM25066 interfaces with a low-cost external diode for monitoring the temperature of the external MOSFET or other thermally sensitive components. The POWER GOOD output provides a fast indicator when the input and/or output voltages are outside their programmed range. LM25066 current measurement accuracy is ±2.4% over temperature.

The LM25066 monitoring block computes both the real-time and average values of subsystem operating parameters (VIN, IIN, PIN, VOUT) as well as the peak power. Accurate power averaging is accomplished by averaging the product of the input voltage and current. A black box (Telemetry/Fault Snapshot) function captures and stores telemetry data and device status in the event of a warning or a fault.
filter 尋找其它 eFuses 和熱插拔制器
下載 觀看有字幕稿的影片 影片

您可能會感興趣的類似產品

open-in-new 比較替代產品
引腳對引腳且具備與所比較裝置相同的功能
LM25066A 現行 具更高監控精度與 I2C 和 PMBus 的 2.9V 至 17-V 熱插拔控制器 This product has a higher current monitor accuracy..
功能相同，但引腳輸出與所比較的裝置不同
LM5066 現行 具電流、電壓和電源監控及 PMBus 的 10 V 至 80 V 熱插拔控制器 This product has a higher input voltage range (9-80V).
TPS25985 現行 具有精確和快速電流監視器的 4.5-V 至 16-V、0.59-mΩ、80-A 堆疊式精巧 eFuse Controller with integrated MOSFET, higher current density and stackable.
TPS25990 現行 具備數位遙測控制器的 2.9-V 至 16-V、0.79-mΩ、60-A eFuse Integrated MOSFET, higher current density and stackable
功能與所比較的裝置相似
LM25069 現行 具功率限制和電源良好的 2.9-V 至 17-V 熱插拔控制器 This product has a positive low voltage power limiting hot swap controller.

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 12
類型 標題 日期
* Data sheet LM25066 System Power Management and Protection IC With PMBus™ datasheet (Rev. J) PDF | HTML 2016年 1月 6日
Application note Implementation of PSYS Monitor Using TPS25984, TPS25985, or TPS25990 eFuses PDF | HTML 2023年 11月 15日
E-book 11 Ways to Protect Your Power Path 2019年 7月 3日
Selection guide Power Management Guide 2018 (Rev. R) 2018年 6月 25日
Technical article Simplify digital hot swap design using the PI-Commander GUI PDF | HTML 2016年 6月 6日
Technical article Building blocks of power PDF | HTML 2016年 3月 23日
Technical article Simplify robust hot-swap design using design calculator tools PDF | HTML 2016年 3月 4日
Selection guide Hot Swap Selection Tool 2015年 7月 28日
Application note Handling System Transients in Hot Swap Applications 2015年 5月 8日
Application note Robust Hot Swap Design (Rev. A) 2015年 4月 8日
User guide AN-2100 LM25066 Evaluation Board (Rev. C) 2013年 4月 26日
User guide AN-2160 LM5066 Evaluation Board (Rev. A) 2013年 4月 26日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

LM25066EVK — 適用於 LM25066 的評估板

The LM25066EVK evaluation module (EVM) is a fully assembled and tested circuit for evaluating the LM25066 hot-swap controller with PMBUS compliant SMBUS/I2C interface to accurately measure, protect and control the electrical operating conditions of systems connected to a backplane power bus. The (...)

使用指南: PDF
TI.com 無法提供
開發模組 (EVM) 的 GUI

PMBUSMGRGUI-SW — LM25066, LM5066, LM5064, LM25056 PMBus Manager GUI

Companion GUI for evaluation boards supporting: LM25066, LM5066, LM5064 Hot Swap + telemetry devices and the LM25056 telemetry-only device

支援產品和硬體

支援產品和硬體

產品
eFuses 和熱插拔制器
LM25066 — 具 PMBus 的 2.9-V 至 17-V 熱插拔控制器 LM25066I — 具內部節點管理工具與 I2C 和 PMBus 的 2.9V 至 17-V 熱插拔控制器 LM5064 — 具 PMBus 的 -10-V 至 -80-V 熱插拔控制器 LM5066 — 具電流、電壓和電源監控及 PMBus 的 10 V 至 80 V 熱插拔控制器
數位電源監測器
LM25056 — 3 至 17V、12 位元 pmbus 輸出電流/電壓/功率/溫度監控器
硬體開發
開發板
LM5066EVK — LM5066 評估套件
下載
開發模組 (EVM) 的 GUI

SLVC572 — PI-Commander EVM GUI

支援產品和硬體

支援產品和硬體

產品
eFuses 和熱插拔制器
LM25066 — 具 PMBus 的 2.9-V 至 17-V 熱插拔控制器 LM25066A — 具更高監控精度與 I2C 和 PMBus 的 2.9V 至 17-V 熱插拔控制器 LM25066I — 具內部節點管理工具與 I2C 和 PMBus 的 2.9V 至 17-V 熱插拔控制器 LM25066IA — 具 I2C 和 PMBus 的 2.9V 至 17-V 熱插拔控制器 - 具更高監控精度與內部節點 LM5064 — 具 PMBus 的 -10-V 至 -80-V 熱插拔控制器 LM5066 — 具電流、電壓和電源監控及 PMBus 的 10 V 至 80 V 熱插拔控制器 LM5066I — 具進階電流、電壓和電源監控準確度的 10 V 至 80 V 熱插拔控制器
供電設備
TPS23861 — 具自主模式的 2 對、Type-2、4 通道 PoE PSE
硬體開發
開發板
LM5056EVM — LM5056 高電壓系統電源管理 IC 評估模組 TPS23861EVM-612 — 適用於四路 IEEE 802.3at PoE PSE 控制器的 TPS23861EVM-612 評估模組
下載
支援軟體

SNVU310 — LM25066 Design Calculator

支援產品和硬體

支援產品和硬體

產品
eFuses 和熱插拔制器
LM25066 — 具 PMBus 的 2.9-V 至 17-V 熱插拔控制器 LM25066A — 具更高監控精度與 I2C 和 PMBus 的 2.9V 至 17-V 熱插拔控制器 LM25066I — 具內部節點管理工具與 I2C 和 PMBus 的 2.9V 至 17-V 熱插拔控制器 LM25066IA — 具 I2C 和 PMBus 的 2.9V 至 17-V 熱插拔控制器 - 具更高監控精度與內部節點
下載
計算工具

SNVR505 — LM25066 Design Calculator With FET Recommendation

支援產品和硬體

支援產品和硬體

產品
eFuses 和熱插拔制器
LM25066 — 具 PMBus 的 2.9-V 至 17-V 熱插拔控制器 LM25066A — 具更高監控精度與 I2C 和 PMBus 的 2.9V 至 17-V 熱插拔控制器 LM25066I — 具內部節點管理工具與 I2C 和 PMBus 的 2.9V 至 17-V 熱插拔控制器 LM25066IA — 具 I2C 和 PMBus 的 2.9V 至 17-V 熱插拔控制器 - 具更高監控精度與內部節點
下載
計算工具

TVS-RECOMMENDATION-CALC — TVS diode recommendation tool

This tool suggests suitable TVS for given system parameters and abs max voltage rating of the device.
支援產品和硬體

支援產品和硬體

此設計資源支援此類別中多數產品。

檢查產品詳細資料頁面以確認支援。
下載
模擬工具

PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具

PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
要求
封裝 針腳 CAD 符號、佔位空間與 3D 模型
WQFN (NHZ) 24 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片