MSP430FG6426
MCU a 20 MHz con 128 KB de memoria flash, 10 KB de SRAM, ADC Sigma-Delta de 16 bits, DAC dual, DM
MSP430FG6426
- Low supply voltage range: 3.6 V down to 1.8 V
- High-performance integrated signal chain
- Continuous-time sigma-delta 16-bit analog-to-digital converter (ADC) with internal reference with 10 external analog inputs, 6 single-ended and 4 selectable as differential or single-ended
- Dual operational amplifiers
- Quad low-impedance ground switches
- Voltage comparator
- Dual 12-bit digital-to-analog converters (DACs) with synchronization
- Integrated LCD driver with contrast control for up to 160 segments
- MSP430FG662x: Full-speed universal serial bus (USB)
- Integrated USB-PHY
- Integrated 3.3-V and 1.8-V USB power system
- Integrated USB-PLL
- Eight input and eight output endpoints
- Ultra-low power consumption
- Active mode (AM), all system clocks active: 250 µA/MHz at 8 MHz, 3.0 V, flash program execution (typical)
- Standby mode (LPM3): watchdog with crystal, and supply supervisor operational, full RAM retention, fast wakeup: 3.2 µA at 2.2 V, 3.4 µA at 3.0 V (typical)
- Shutdown RTC mode (LPM3.5): shutdown mode, active RTC with crystal: 0.9 µA at 3.0 V (typical)
- Shutdown mode (LPM4.5): 0.2 µA at 3.0 V (typical)
- Intelligent digital peripherals
- Two 16-bit timers with three capture/compare registers each
- One 16-bit timer with five capture/compare registers
- One 16-bit timer with seven capture/compare registers
- 6-channel internal DMA
- Hardware multiplier supports 32-bit operations
- Four universal serial communication interfaces (USCIs)
- USCI_A0 and USCI_A1
- Enhanced UART with automatic baud-rate detection
- IrDA encoder and decoder
- Synchronous SPI
- USCI_B0 and USCI_B1
- I2C
- Synchronous SPI
- USCI_A0 and USCI_A1
- RTC with calibration logic for time offset correction, operation in LPM 3.5
- 16-bit RISC architecture, extended memory, up to 20-MHz system clock
- Flexible power-management system
- Fully integrated LDO with programmable regulated core supply voltage
- Supply voltage supervision, monitoring, and brownout
- Unified clock system
- FLL control loop for frequency stabilization
- Low-power low-frequency internal clock source (VLO)
- Low-frequency trimmed internal reference source (REFO)
- 32-kHz crystals (XT1)
- High-frequency crystals up to 32 MHz (XT2)
- Separate voltage supply for backup subsystem
- 32-kHz low-frequency oscillator (XT1)
- RTC
- Backup memory (8 bytes)
- Development tools and software (also see Tools and Software)
- MSP-TS430PZ100AUSB 100-pin target development board
- MSP430Ware™ code examples
- Wake up from standby mode in 3 µs (typical)
- Serial onboard programming, no external programming voltage needed
- Available in 100-pin LQFP and 113-pin Microstar Junior™ BGA packages
- Device Comparison summarizes the available family members
The Texas Instruments MSP430FG662x and MSP430FG642x microcontrollers (MCUs) are part of the MSP430TM Metrology and Monitoring portfolio. The architecture and integrated peripherals, combined with five extensive low-power modes, are optimized to achieve extended battery life in portable and battery-powered measurement applications. The device features a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code efficiency. The digitally controlled oscillator (DCO) allows the devices to wake up from low-power modes to active mode in less than 5 µs.
The MSP430FG662x MCUs are targeted at small signal-monitoring applications and include a 16-bit sigma-delta ADC, dual low-power operational amplifiers, dual 12-bit DACs, voltage comparator, four USCIs (two USCI_A modules and two USCI_B modules), four 16-bit timers, a hardware multiplier, a DMA module, an RTC module, an LCD driver with integrated contrast control for up to 160 segments, integrated full-speed USB, an auxiliary supply system, up to 128KB flash, 10KB SRAM and 73 I/O pins in 100‑pin devices and 113‑pin devices.
The MSP430FG642x MCUs are targeted at small-signal monitoring applications and include a 16-bit sigma-delta ADC, dual low-power operational amplifiers, dual 12-bit DACs, voltage comparator, four USCIs (two USCI_A modules and two USCI_B modules), four 16-bit timers, a hardware multiplier, a DMA module, an RTC module, an LCD driver with integrated contrast control for up to 160 segments, an auxiliary supply system, up to 128KB of flash, 10KB of SRAM, and 73 I/O pins in 100‑pin devices and 113‑pin devices.
Typical applications for these microcontrollers include small signal-monitoring applications such as handheld test and measurement equipment, field transmitters, and blood glucose meters. These microcontrollers can reduce overall system cost through high analog integration and enable long battery life by low-power operation.
The MSP430FG662x and MSP430FG642x MCUs are supported by an extensive hardware and software ecosystem with reference designs and code examples to get your design started quickly. Development kits include the MSP-TS430PZ100AUSB 100-pin target development board. TI also provides free MSP430Ware™ software, which is available as a component of Code Composer Studio™ IDE desktop and cloud versions within TI Resource Explorer. The MSP430 MCUs are also supported by extensive online collateral, training, and online support through the TI E2E™ support forums.
For complete module descriptions, see the MSP430F5xx and MSP430F6xx Family Users Guide.
Documentación técnica
Diseño y desarrollo
Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.
MSP-FET430U100AUSB — Placa de desarrollo destino de 100 pines y paquete MSP-FET - MSP430FG6x MCU-Microcontroladores no in
Note: This kit does not include MSP430FG6x2x microcontroller samples. To sample the compatible devices, please visit the product page or select the related MCU after adding the tool to the TI Store cart:
The MSP-FET is a powerful flash emulation tool (...)
MSP-FET — Programador y depurador de MSP MCU
The MSP-FET is a powerful emulation development tool – often called a debug probe – which allows users to quickly begin development on MSP low-power microcontrollers (MCU).
It supports programming and real-time debugging over both JTAG and SBW interfaces. Furthermore, the MSP-FET also provides a (...)
MSP-GANG — Programador de producción MSP-GANG
El programador de MSP Gang (MSP-GANG) es un programador de dispositivos MSPM0/MSP430™/MSP432™ que puede programar hasta ocho dispositivos Flash o FRAM MSPM0/MSP430/MSP432 idénticos al mismo tiempo. Se conecta a una PC host mediante una conexión RS-232 o USB estándar y proporciona (...)
MSP-DSPLIB — Digital Signal Processing (DSP) Library for MSP Microcontrollers
The TI MSP430™ Digital Signal Processing library is a set of optimized functions to perform common signal processing operations for MSP430 microcontrollers. These functions are used in applications where processing-intensive transforms are done in real-time for minimal energy and with very (...)
Productos y hardware compatibles
Productos
Microcontroladores MSP430
Otras interfaces
TI-DEVELOPER-ZONE — Start embedded development on your desktop or in the cloud
Productos y hardware compatibles
Productos
MCU Arm Cortex-M0+
Microcontroladores MSP430
Productos Wi-Fi
MCU Arm Cortex-R
Procesadores basados en Arm
Microcontroladores en tiempo real C2000
Productos de 2.4 GHz de baja potencia
MCU inalámbricas Sub-1 GHz
Desarrollo de hardware
Placa de evaluación
CCSTUDIO — Code Composer Studio™ integrated development environment (IDE)
Code Composer Studio is an integrated development environment (IDE) for TI's microcontrollers and processors. It comprises a suite of tools used to develop and debug embedded applications. Code Composer Studio is available for download across Windows®, Linux® and macOS® desktops. It can also (...)
Productos y hardware compatibles
Este recurso de diseño es compatible con la mayoría de los productos de estas categorías.
Revise la página de detalles del producto para verificar la compatibilidad.
-
parametric-filter Procesadores digitales de señales (DSP) -
parametric-filter Procesadores basados en Arm -
parametric-filter Microcontroladores MSP430 -
parametric-filter Microcontroladores en tiempo real C2000 -
parametric-filter Microcontroladores basados en Arm -
parametric-filter Acondicionadores de señal -
parametric-filter Sensores de radar mmWave -
parametric-filter Productos Zigbee -
parametric-filter Productos Wi-Fi -
parametric-filter Productos roscados -
parametric-filter Otras tecnologías inalámbricas -
parametric-filter Productos Sub-1 GHz -
parametric-filter Productos multiprotocolo -
parametric-filter Productos Bluetooth -
parametric-filter Drivers aislados de alimentación digital
CCSTUDIO-THEIA — Code Composer Studio™ integrated development environment (IDE) Theia
Code Composer Studio is an integrated development environment (IDE) for TI's microcontrollers and processors. It comprises a suite of tools used to develop and debug embedded applications. Code Composer Studio is available for download across Windows®, Linux® and macOS® desktops. It can also (...)
Productos y hardware compatibles
Productos
MCU Arm Cortex-M0+
MCU inalámbricas Sub-1 GHz
Productos de conectividad inalámbrica automotriz
Productos de 2.4 GHz de baja potencia
Microcontroladores MSP430
Microcontroladores en tiempo real C2000
MCU Arm Cortex-R
Procesadores basados en Arm
Sensores de radar mmWave para automoción
Sensores industriales de radar mmWave
Otros productos inalámbricos
Desarrollo de hardware
Placa de evaluación
Software
Kit de desarrollo de software (SDK)
IAR-KICKSTART — IAR Embedded Workbench
MSP430-ACADEMY — MSP430™ academy
Productos y hardware compatibles
Productos
Microcontroladores MSP430
Desarrollo de hardware
Placa de evaluación
Kit de desarrollo
MSP-GANG-SOFTWARE — MSP-GANG Software
Productos y hardware compatibles
Productos
MCU Arm Cortex-M0+
Microcontroladores MSP430
Desarrollo de hardware
Placa de evaluación
Kit de desarrollo
UNIFLASH — UniFlash for most TI microcontrollers (MCUs) and mmWave sensors
UniFlash is a software tool for programming on-chip flash on TI microcontrollers and wireless connectivity devices and on-board flash for TI processors. UniFlash provides both graphical and command-line interfaces.
UniFlash can be run from the cloud on the TI Developer Zone or downloaded and used (...)
Productos y hardware compatibles
Productos
Microcontroladores en tiempo real C2000
Procesadores basados en Arm
Sensores industriales de radar mmWave
Sensores de radar mmWave para automoción
Microcontroladores MSP430
Productos Wi-Fi
MCU Arm Cortex-M4
MCU Arm Cortex-M0+
MCU Arm Cortex-R
Productos de 2.4 GHz de baja potencia
Productos de conectividad inalámbrica automotriz
MCU inalámbricas Sub-1 GHz
MSP430FG6626 TINA-TI Reference Design
MSP-3P-SEARCH — Herramienta de búsqueda de terceros de MSP
(...)
TIDM-VOICEBANDAUDIO — Reproducción de audio de banda de voz mediante un DAC PWM
Encapsulado | Pines | Símbolos CAD, huellas y modelos 3D |
---|---|---|
LQFP (PZ) | 100 | Ultra Librarian |
Pedidos y calidad
- RoHS
- REACH
- Marcado del dispositivo
- Acabado de plomo/material de la bola
- Clasificación de nivel de sensibilidad a la humedad (MSL) / reflujo máximo
- Estimaciones de tiempo medio entre fallas (MTBF)/fallas en el tiempo (FIT)
- Contenido del material
- Resumen de calificaciones
- Monitoreo continuo de confiabilidad
- Lugar de fabricación
- Lugar de ensamblaje
Soporte y capacitación
Foros de TI E2E™ con asistencia técnica de los ingenieros de TI
El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.
Si tiene preguntas sobre la calidad, el paquete o el pedido de productos de TI, consulte el soporte de TI.